Cechy
- Waga dostawy: 0,023kg
- Wysokość wysyłki: 8mm
- Szerokość wysyłki: 62mm
- Długość wysyłki: 166mm
Nr produktu: 310150002
Nr prod.: NONE
Słynny stolarz Jerry Fisher mówi: "W ciągu 20 lat pracy w stolarstwie to najlepszy skrobak do wlotów, jakiego kiedykolwiek używałem, a próbowałem kilku. Po prostu trzymaj go jak ołówek i pracuj od prawej do lewej lub od lewej do prawej, w zależności od kierunku włókien drewna." Precyzyjnie naostrzony z wytrzymałej stali narzędziowej, gotowy do użycia. Instrukcje w zestawie. Trzy narzędzia, z których każde ma dwa różne rozmiary głowic. Podane wymiary dotyczą rozmiarów głowic tnących.
Darmowa wysyłka od 999,00 zł.
Czas dostawy ok. 14-21 dni.
Duży skrobak do inlety JERRY FISHER to narzędzie, które jest używane od ponad 20 lat przez jednego z najlepszych w branży. Znany rzemieślnik Jerry Fisher mówi: "W ciągu 20 lat pracy w branży, to jest najlepszy skrobak do inlety, jakiego kiedykolwiek używałem, a próbowałem ich wielu. Po prostu trzymaj go jak ołówek i pracuj od prawej do lewej lub od lewej do prawej, w zależności od kierunku włókien drewna."
Narzędzie jest precyzyjnie szlifowane z wytrzymałej stali narzędziowej, naostrzane i gotowe do użycia. W zestawie znajdują się instrukcje obsługi oraz trzy narzędzia, z których każde ma dwa różne rozmiary głowic.
Good Tool for Scraping any Flat Wood 11-12-2014
I have used Jerry Fisher scrapers for 30 years.
This flat scaper allows you to work any flat surface in the inletting. It ca also be used to clean up edge in places like a shadow line cheeck piece.
SPECTACULAR PRODUCT 12-03-2011
First ..I am a first time user and a first time maker of a fore end for a Schutzen fore end. I started out with a 3/4 " burr placed in a drill press to set the initial path of the burr . I found the that I would have to set the fore end piece in a drill press vice so that the wood would slide in the vice. I also the found that I even had to tip the piece to engage the burr into the wood (English Walnut) This at least, set the path for the beginning of the inletting for a tapered barrel. (swamped barrel) After taking a bounty paper towel (no interest...just love them )I was able to take the inletting black, also from Brownells (I think the gold would have been too light ..I am 70 years old so....)Coating the barrel with the black and the spinning it into the the new started barrel grouve I found that this scraper while just removing the highlighted black area ...many many times produced a barrel grouve inlett that was not only perfect but put my inlet actually a little low, Perfect, now I could sand or scrape off to make the top surface perfect with the appropriate depth. This was great because I lost control of the tool (my error) the top surface was then perfect. I purchased the other barrel inletting tools in anticapation of problems...don't bother...just buy the scraper...in fact buy them both ...large and small. I only purchased the small ...I could have used the large in the swamped barrel but I managed to do fine. I do not have a financial interest in this company , but I wish I did. I hope this may be beneficial to you in your inletting. Bill
Napotkaliśmy błąd podczas wczytywania tej zawartości. Odśwież stronę, aby kontynuować. Jeśli problem będzie się powtarzał, skontaktuj się z naszym działem obsługi klienta.