Cechy
- Model: XD
- Rodzaj wykończenia: Black
- Styl: Competition
- Typ broni: Springfield
- Waga dostawy: 0,05kg
- Wysokość wysyłki: 15mm
- Szerokość wysyłki: 109mm
- Długość wysyłki: 191mm
- UPC: 686461783067
Szczegóły pozycji
US export classification: 0A501.c

Nr produktu: 100009890
Nr prod.: PRP-042-9-40
686461783067 Zestaw zawiera słynną dźwignię bezpieczeństwa strzału firmy Powder River Precision, która eliminuje długi pre-travel spustu w modelu XD. W zestawie znajdują się również sprężyny spustu i mechanizmu o obniżonej mocy, co pozwala na zmniejszenie wagi spustu. Nowy spust ma opatentowany kąt, który pomaga w odciążeniu spustu i zapewnia gładkie, wyraźne zerwanie. Spust wykonany jest z wytrzymałego, lekkiego polimeru, co przyspiesza reset. Posiada również wbudowaną blokadę nadmiernego ruchu z tyłu spustu. Użycie tej metody blokady nadmiernego ruchu redukuje dodatkowe obciążenie na belce spustowej. Po prawidłowym zainstalowaniu, zestaw zapewni krótki, wyraźny nacisk spustu (około 3.5-4 funty) z szybkim resetem i skróci całkowitą długość nacisku spustu o około 1/2. Zestaw wymaga drobnego dopasowania i zawiera instrukcje instalacji dla rusznikarzy. Pasuje do wszystkich modeli XD (ZA WYJĄTKIEM modelu XD 45 z dźwignią bezpieczeństwa lub nowych modeli XD). Ten spust jest oryginalną częścią Springfield Armory dostępną w produkcji pistoletów XD i XDM.Zestaw XD ULTIMATE MATCH TARGET TRIGGER KITS od POWDER RIVER PRECISION INC to idealne rozwiązanie dla każdego właściciela pistoletu XD, który pragnie poprawić precyzję i komfort strzelania.
Well worth it 18-04-2017
I'm no gunsmith but this is easy enough to install. Takes some patience to fit the pieces properly without taking off too much but it is well worth the time. The trigger pull is noticeably much lighter, the break is much more crisp, and pre travel and over travel are minimized greatly. I was going to adjust my rear sight because I tend to shoot left with all handguns but with this trigger I'm back in the bullseye with much tighter groups. Go slow with the fitting, I had to remove almost the entire raised ridge on the side of the sear, a very small amount from the back of the sear so the grip safety wouldn't stick, and some on the back of the trigger over travel stop.
Powder River Ultimare Match Trigger 22-01-2016
Just finished installing this trigger in an older Springfield XD 45. Trigger pull was reduced 48% from factory pull of 7 pounds. Pre-travel was also reduced by roughly 50%. These specs were exactly as advertised by Powder River. The sear, striker safety lever and integral over-travel on the back of the replacement trigger all had to be fit by hand. The trickiest part of the job is fitting the striker safety lever to the pistol. If the safety lever does not depress far enough to clear the striker safety mounted in the slide, you're going to have one hell of a time getting the slide back off the frame of the pistol. Pay attention to the amount of downward travel in the original striker safety lever in relation to the back slide rail. In my pistol the original safety lever was pretty close to flush with the top of the frame rail. I duplicated the same approximate distance of downward travel on the replacement part. I recommend a good oil stone for use on the side of the sear and small reset tab on the inside of the safety lever. A file works just fine for filing the over-travel stop on the back side of the replacement trigger. Read the manufacturer's instructions carefully. Patience is a virtue on this job. You can always take a little more material off. It's gonna be hell getting any material to go back on.
Napotkaliśmy błąd podczas wczytywania tej zawartości. Odśwież stronę, aby kontynuować. Jeśli problem będzie się powtarzał, skontaktuj się z naszym działem obsługi klienta.