Aby zamontować celownik Vortex Razor, C-More RTS lub STS typu red-dot, wystarczy zdjąć tylny przyrząd celowniczy z broni i zastąpić go montażem EGW. W każdej chwili możesz zdjąć montaż i ponownie zamontować tylny przyrząd celowniczy. Zestaw zawiera elementy montażowe. Instrukcja instalacji: Usuń tylny przyrząd celowniczy* Zainstaluj montaż EGW w rowku Przykręć śrubę ustalającą (jeśli dotyczy) Umieść celownik red-dot na montażu EGW (umieszczenie małego kawałka papieru między celownikiem red-dot a montażem ułatwi późniejsze usunięcie i ochroni celownik przed Loctite) Nałóż niebieski Loctite na dostarczone śruby montażowe Dokręć śruby montażowe z momentem 15in/lbs Śruby dołączone do tego montażu wymagają klucza imbusowego 5/64'' do instalacji. Ten montaż pasuje do: Wszystkich modeli XD, które NIE są modelami przygotowanymi pod optykę (Optics Ready Model) W skład tego wchodzą, ale nie ograniczają się do: Springfield XD® MOD.2® – 3"" SUB-COMPACT MODEL Springfield XD® MOD.2® – 3.3"" SUB-COMPACT MODEL Springfield XD® MOD.2® – 4"" SERVICE MODEL Springfield XD® MOD.2® – 4"" SERVICE MODEL THREADED BARREL Springfield XD® MOD.2® – 5"" TACTICAL MODEL Springfield XD® 3"" SUB-COMPACT MODEL Springfield XD® 4"" SERVICE MODEL Springfield XD(M)® 3.8"" COMPACT MODEL Springfield XD(M)® 3.8"" MODEL Springfield XD(M)® 4.5"" MODEL Springfield XD(M)® 4.5"" THREADED BARREL MODEL Springfield XD-S® 3.3"" MODEL Springfield XD-E™ 3.3"" SINGLE STACK Springfield XD-E™ 3.8"" SINGLE STACK Nie pasuje do: Springfield XD(M)® 5.25"" COMPETITION SERIES MODEL Żadnego modelu Springfield XD przygotowanego pod optykę (Optics Ready)
Więcej...
Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: All XD Models that are NOT the Optics Ready Model This includes, but is not limited to: Springfield XD® MOD.2® – 3"" SUB-COMPACT MODEL Springfield XD® MOD.2® – 3.3"" SUB-COMPACT MODEL Springfield XD® MOD.2® – 4"" SERVICE MODEL Springfield XD® MOD.2® – 4"" SERVICE MODEL THREADED BARREL Springfield XD® MOD.2® – 5"" TACTICAL MODEL Springfield XD® 3"" SUB-COMPACT MODEL Springfield XD® 4"" SERVICE MODEL Springfield XD(M)® 3.8"" COMPACT MODEL Springfield XD(M)® 3.8"" MODEL Springfield XD(M)® 4.5"" MODEL Springfield XD(M)® 4.5"" THREADED BARREL MODEL Springfield XD-S® 3.3"" MODEL Springfield XD-E™ 3.3"" SINGLE STACK Springfield XD-E™ 3.8"" SINGLE STACK Does not fit: Springfield XD(M)® 5.25"" COMPETITION SERIES MODEL Any Optics Ready Springfield XD
Więcej...
3443441PLN
Nr produktu: 296000695 EGW SIGHT MOUNT FOR VORTEX RAZOR FITS SPRINGFIELD XD/XDM BLACK Numer części: 49442841370113057 Aby zamontować celownik Vortex Razor, C-More RTS lub STS typu red-dot, wystarczy zdjąć tylny przyrząd celowniczy z broni i zastąpić go montażem EGW. W każdej chwili możesz zdjąć montaż i ponownie zamontować tylny przyrząd celowniczy. Zestaw zawiera elementy montażowe. Instrukcja instalacji: Usuń tylny przyrząd celowniczy* Zainstaluj montaż EGW w rowku Przykręć śrubę ustalającą (jeśli dotyczy) Umieść celownik red-dot na montażu EGW (umieszczenie małego kawałka papieru między celownikiem red-dot a montażem ułatwi późniejsze usunięcie i ochroni celownik przed Loctite) Nałóż niebieski Loctite na dostarczone śruby montażowe Dokręć śruby montażowe z momentem 15in/lbs Śruby dołączone do tego montażu wymagają klucza imbusowego 5/64'' do instalacji. Ten montaż pasuje do: Wszystkich modeli XD, które NIE są modelami przygotowanymi pod optykę (Optics Ready Model) W skład tego wchodzą, ale nie ograniczają się do: Springfield XD® MOD.2® – 3"" SUB-COMPACT MODEL Springfield XD® MOD.2® – 3.3"" SUB-COMPACT MODEL Springfield XD® MOD.2® – 4"" SERVICE MODEL Springfield XD® MOD.2® – 4"" SERVICE MODEL THREADED BARREL Springfield XD® MOD.2® – 5"" TACTICAL MODEL Springfield XD® 3"" SUB-COMPACT MODEL Springfield XD® 4"" SERVICE MODEL Springfield XD(M)® 3.8"" COMPACT MODEL Springfield XD(M)® 3.8"" MODEL Springfield XD(M)® 4.5"" MODEL Springfield XD(M)® 4.5"" THREADED BARREL MODEL Springfield XD-S® 3.3"" MODEL Springfield XD-E™ 3.3"" SINGLE STACK Springfield XD-E™ 3.8"" SINGLE STACK Nie pasuje do: Springfield XD(M)® 5.25"" COMPETITION SERIES MODEL Żadnego modelu Springfield XD przygotowanego pod optykę (Optics Ready)
344PLN1344,00 zł
*
Czas dostawy ok. 14-21 dni. 1 szt. w magazynie w USA
Specyfikacja:Color: BlackMake: SpringfieldMaterial: AluminumModel: XD-Subcompact, XDS, XDM, XD Mod 2, XD-ENumber of Bases: 1-PieceStyle: Tactical
Aby zamontować celownik Vortex Razor, C-More RTS lub STS typu red-dot, wystarczy zdjąć tylny przyrząd celowniczy z broni i zastąpić go montażem EGW. W każdej chwili możesz zdjąć montaż i ponownie zamontować tylny przyrząd celowniczy. Zestaw zawiera elementy montażowe. Instrukcja instalacji: Usuń tylny przyrząd celowniczy* Zainstaluj montaż EGW w rowku Przykręć śrubę ustalającą (jeśli dotyczy) Umieść celownik red-dot na montażu EGW (umieszczenie małego kawałka papieru między celownikiem red-dot a montażem ułatwi późniejsze usunięcie i ochroni celownik przed Loctite) Nałóż niebieski Loctite na dostarczone śruby montażowe Dokręć śruby montażowe z momentem 15in/lbs Śruby dołączone do tego montażu wymagają klucza imbusowego 5/64'' do instalacji. Ten montaż pasuje do: Wszystkich modeli XD, które NIE są modelami przygotowanymi pod optykę (Optics Ready Model) W skład tego wchodzą, ale nie ograniczają się do: Springfield XD® MOD.2® – 3"" SUB-COMPACT MODEL Springfield XD® MOD.2® – 3.3"" SUB-COMPACT MODEL Springfield XD® MOD.2® – 4"" SERVICE MODEL Springfield XD® MOD.2® – 4"" SERVICE MODEL THREADED BARREL Springfield XD® MOD.2® – 5"" TACTICAL MODEL Springfield XD® 3"" SUB-COMPACT MODEL Springfield XD® 4"" SERVICE MODEL Springfield XD(M)® 3.8"" COMPACT MODEL Springfield XD(M)® 3.8"" MODEL Springfield XD(M)® 4.5"" MODEL Springfield XD(M)® 4.5"" THREADED BARREL MODEL Springfield XD-S® 3.3"" MODEL Springfield XD-E™ 3.3"" SINGLE STACK Springfield XD-E™ 3.8"" SINGLE STACK Nie pasuje do: Springfield XD(M)® 5.25"" COMPETITION SERIES MODEL Żadnego modelu Springfield XD przygotowanego pod optykę (Optics Ready)
Więcej...
Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: All XD Models that are NOT the Optics Ready Model This includes, but is not limited to: Springfield XD® MOD.2® – 3"" SUB-COMPACT MODEL Springfield XD® MOD.2® – 3.3"" SUB-COMPACT MODEL Springfield XD® MOD.2® – 4"" SERVICE MODEL Springfield XD® MOD.2® – 4"" SERVICE MODEL THREADED BARREL Springfield XD® MOD.2® – 5"" TACTICAL MODEL Springfield XD® 3"" SUB-COMPACT MODEL Springfield XD® 4"" SERVICE MODEL Springfield XD(M)® 3.8"" COMPACT MODEL Springfield XD(M)® 3.8"" MODEL Springfield XD(M)® 4.5"" MODEL Springfield XD(M)® 4.5"" THREADED BARREL MODEL Springfield XD-S® 3.3"" MODEL Springfield XD-E™ 3.3"" SINGLE STACK Springfield XD-E™ 3.8"" SINGLE STACK Does not fit: Springfield XD(M)® 5.25"" COMPETITION SERIES MODEL Any Optics Ready Springfield XD