Rozszerzona dźwignia zwalniania poprawia szybkość wymiany magazynów i ułatwia usuwanie zacięć, umożliwiając obsługę jedną ręką bez zdejmowania ręki z uchwytu.
813318020215 Przedłużony dźwignia zwolnienia przyspiesza wymianę magazynków i zwiększa zdolność strzelca do szybkiego i bezpiecznego usuwania zacięć, podwójnych nabojów i awarii. Umożliwia chwycenie i zwolnienie zamka palcem wskazującym wewnątrz osłony spustu, zamiast przy użyciu ręki dominującej. Naciśnij w górę na dźwigni, aby zablokować zamek w tylnym położeniu; lekko naciśnij w dół, aby go zwolnić. Obie operacje można wykonać bez zdejmowania ręki z uchwytu pistoletowego. EBRv2/308 to niskoprofilowy, łatwy do zamontowania zamiennik dla fabrycznego zwolnienia we wszystkich modelach serii DPMS LR-308 karabinów typu AR w kal. .308, a także dla Remington R-25 w kal. .308, .243 i 7mm-08. Niekompatybilny z karabinami typu Armalite i DPMS Gen 2.
W magazynie
5 szt. w magazynie w USA
Darmowa wysyłka od 999,00 zł.
Czas dostawy ok. 14-21 dni.
Wydajny mechanizm zwolnienia zamka dla lepszej obsługi broni
Rozszerzony mechanizm zwolnienia zamka 308 AR V2 (EBRV2/308) od PHASE 5 TACTICAL przyspiesza wymianę magazynków oraz zwiększa zdolność strzelca do szybkiego i bezpiecznego usuwania zacięć, podwójnych załadunków i awarii. Umożliwia chwycenie i zwolnienie zamka palcem wskazującym wewnątrz osłony spustu, zamiast używać drugiej ręki.
Funkcjonalność
Naciśnij w górę na dźwignię, aby zablokować zamek w pozycji tylniej;
Naciśnij lekko w dół, aby go zwolnić.
Obie operacje można wykonać bez odrywania ręki od chwytu pistoletowego.
Kompatybilność
EBRv2/308 to niski profil, łatwy do zainstalowania zamiennik dla fabrycznego zwolnienia w wszystkich modelach serii DPMS LR-308 oraz w Remington R-25 w kalibrze .308, .243 i 7mm-08. Niekompatybilny z karabinami Armalite oraz DPMS Gen 2.
Dane techniczne
Materiał: stal obrabiana skrawaniem
Wykończenie: matowa czerń
Długość: 2¼" (5.3 cm)
Waga: ½ oz. (14 g)
Extended release lever speeds magazine changes and enhances the shooter’s ability to clear jams, double feeds, and malfunctions quickly and safely. Lets you catch and release the bolt with the trigger finger inside the triggerguard, instead of with your off hand. Push upward on the lever to lock the bolt rearward; push lightly downward to release it. Both operations can be performed without removing your hand from the pistol grip. EBRv2/308 is the same low-profile, drop-in replacement for the factory release on all models of the DPMS LR-308 series of AR-style .308 rifles, as well as the Remington R-25 in .308, .243, and 7mm-08. Not compatible with Armalite and DPMS Gen 2 style rifles
SPECS: Machined steel, matte black finish. 2¼" (5.3cm) long. ½ oz. (14g) wt.
Cechy
Typ broni:AR .308
Waga dostawy:0,023kg
Wysokość wysyłki:5mm
Szerokość wysyłki:79mm
Długość wysyłki:150mm
UPC:813318020215
Szczegóły pozycji
Made in USA
US export classification: 0A501.x
Opinie klientów
Oceny klientów (16)
4,1 / 5
Zdecydowanie polecane
A slight wiggle 10-05-2018
This extended bolt release has a slight wiggle, but overall it's a great product. easy to install, fit my Aero M5 lower just fine, looks great and is functional and practical.
Zdecydowanie polecane
Does work on Armalite AR-10 rifles 26-06-2017
Order this on the description of fitting an AR-10. When reviewing the order I noticed the note that it did not for Armalite rifles, it does. Installed it today with little to no effort. Looks great, and works with all my metal magazines. If you use polymer magazines that need a series âAâ bolt stop, it may not work. Be sure of what series you need when ordering.
Polecane
Solid part 16-03-2017
Solid build. I put it on a Black Rain lower. I had to take a dermal and file down part of it so that it would engage properly. I think if they reworked the design a little then fitting wouldn't be necessary. It works flawlessly now. I doubt all lowers require fitting like my Black Rain lower did.
Zdecydowanie polecane
This thing works 29-12-2016
Works perfectly on my R25 using pmags. Easy to install and functions beautifully. Well worth the price imho.
Zdecydowanie polecane
Accidental install on an AR 15 10-02-2016
I bought the 308 version and decided to try it in my Ruger 556 anyways. It fits well and locks back with Pmags every time. I wonder if it might have issues in Non Mil spec uppers as the sidewalls might be thicker and not allow it to pivot far enough to get in front of the bolt.
Zdecydowanie polecane
Great Product 23-11-2015
I purchased this bolt release despite some of the negative reviews, and I am glad I did. I am building a 308 on Aero Precision receivers( DPMS LR308 spec), and this product fit perfectly. I did not have to make any alterations. Installed easily, looks and works great. I feel that the problem others are having is due to the fact that the 308 AR is not mil-spec so there can be many variances between manufactures. All you can do is try it, if it does not fit, return it and try something else. That is all part of the wonderful world of customizing. Good luck and happy building!
Zdecydowanie polecane
Works beautifully. 03-03-2015
I was a bit leery after reading some of the reviews, but still decided to use it on my build. I did make sure to polish it with 600 grit sandpaper and treated the entire lower and parts with froglube prior to assembly. When I dry fit it prior to polishing it, it was a very snug fit, and I can understand where it would cause issues. However, if you put the extra care into it beforehand, it should work phenomenally. I've put over 400 rounds (over 20 mags) through the gun, and I've never had it fail to lock the bolt back. Also, while it holds the bolt quite secure, it doesn't take much pressure to release.
Polecane z zastrzeżeniami
Not the best 11-11-2014
I like the idea and looks but they are hit or miss as to working properly .I think the mass of weight is just to much for it to lock quick enough on last shot to lock bolt back .
Niepolecane
This Does NOT work with a Ruger SR762 28-03-2014
Your expert service said this item would work with a Ruger SR762. I ordered it and found that it would NOT hold the bolt open unless I did some grinding with a Dremel, which I did. It now works but I had to make it fit as it would not open up enough and therefore would barely hold the bolt open, often closing within 1-2 seconds. Do not buy this item for this rifle unless you know how to grind small parts with a Dremel. It will NOT work as a stock item.
Polecane z zastrzeżeniami
Need some tweakng 14-03-2014
Installed it on cmmg lower dpms upper. Installation went smooth at first. Pulled back on my charging handle and would not catch the bcg. I noticed that the left side of the bolt release ( vertical part ) was rubbing against the lower. I had to file / sand down the sides of the bolt release quiet a bit to clear the lower. It works fine now but the strength / integrity of the bolt release has been compromised a little. I would still use this set up on my gun...still beats the standard release.
Polecane
Pretty much only option for .308 08-11-2013
I recently completed a .308 build on a JD Machine lower and this Phase 5 item is pretty much the only game in town if you want a B.A.D. lever on one of these. I've used the Phase 5 on a .223 build without issues, but this application needed a little tweeking and massaging to fit properly even though I was using the appropriate .308 version. Out of the package, this item contacted the lower just slightly, but just enough to prevent the carrier from locking back on an empty mag without manually intervening. After bending the whole lever out just a tad, it now works fine.
Zdecydowanie polecane
Fine engineering 22-10-2013
I found out that most SIG AR platforms will not accept the Magpul extended bolt release extension that clamps on the stock bolt release lever. I got two Phase 5 releases (5.56 and 308) and both fit on to my Sig 516 and 716. They replace the entire bolt release lever and eliminate the wobbliness felt in the Magpul clamp on version. They are a little tricky to put on due to the location of the roll pin holding it place. Be patient and have the right tool. Brownell sell a roll pin punch designed for the bolt release roll pin. Remember to put protective tape around you lower.
Polecane z zastrzeżeniami
Not like its sibling 21-04-2013
Unlike their AR-15 model (100-004-899) this didn't work for me so well.
First, it's not one-piece machining, but rather a cut-down regular bolt catch with the extension welded on.
Second, and the most important point, is that without modification this device would not hold the bolt open on Armalite AR-10. Looking at the original and this catch side by side it becomes obvious that the dimensions are different -- the extended catch is smaller vertically. As it appears that this device is made from an existing bolt catch, it must be from some other model, not Armalite's. From another review it seems that it's not DMPS either.
I finally made it work by enlarging the roll pin hole to about 1/8". It was a tedious process even with a carbide bit, because the part is made from hardened steel.
I still recommend it though, as there is no alternative on the .308 platform.
This kind of device improves ergonomics tremendously.
Zdecydowanie polecane
ambi bolt release 25-11-2012
This device is great, but edges are sharp and could be smoothed out a bit. I placed one on an AR-15, and it needed some additional bending to allow the bolt to catch before it hit the bottom of the lower receiver. It works great now, and I prefer it to any of the bolt one models.
Zdecydowanie polecane
This is awesome. 02-01-2012
Great sigle piece construction. Brownells GET THEIR AMBI CHARGING HANDLE.
Polecane z zastrzeżeniami
model spec. fit 27-06-2011
Installed on a dpms .308 and it would not hold the bolt open. Then installed on a mega mono upper and it work perfectly.
Odpowiedzialny podmiot gospodarczy zgodnie z rozporządzeniem UE
Brownells Polska Sp. z o.o.
Armii Krajowej 77
05-071 Sulejówek
Polska
info@brownells.pl
Instrukcja Bezpieczeństwa dla Przedłużonego Zwolnienia Zasuwnicy 308 AR V2
Wprowadzenie
Dziękujemy za wybór Przedłużonego Zwolnienia Zasuwnicy 308 AR V2 od Phase 5 Tactical. Produkt ten został zaprojektowany w celu poprawy doświadczeń strzeleckich poprzez przyspieszenie wymiany magazynków oraz zwiększenie zdolności do szybkiego usuwania zacięć i awarii. Prosimy o uważne zapoznanie się z niniejszą instrukcją bezpieczeństwa, aby zapewnić bezpieczne i skuteczne użytkowanie produktu.
Ogólne Wytyczne Bezpieczeństwa
Zawsze upewnij się, że twój pistolet jest rozładowany przed zainstalowaniem lub użyciem przedłużonego zwolnienia zasuwy.
Zapoznaj się ze wszystkimi zasadami bezpieczeństwa dotyczącego broni palnej, w tym z właściwym obchodzeniem się i przechowywaniem broni.
Używaj produktu tylko zgodnie z przeznaczeniem i zgodnie z instrukcjami producenta.
Trzymaj produkt z dala od dzieci i osób nieupoważnionych.
Regularnie sprawdzaj produkt pod kątem zużycia lub uszkodzeń przed każdym użyciem.
Zgłaszaj wszelkie niebezpieczne produkty lub wypadki odpowiednim organom.
Specyficzne Środki Ostrożności podczas Użytkowania
Upewnij się, że twój palec znajduje się poza osłoną spustu, gdy nie strzelasz.
Nie próbuj obsługiwać zwolnienia zasuwy, gdy pistolet jest skierowany w stronę siebie lub innych.
Zawsze nos odpowiednią ochronę oczu i uszu podczas używania broni palnej.
Unikaj używania produktu w niekorzystnych warunkach pogodowych, które mogą wpłynąć na twoją przyczepność lub widoczność.
Jeśli doświadczysz jakichkolwiek awarii, natychmiast zaprzestań używania i skonsultuj się z wykwalifikowanym rusznikarzem.
Instrukcje Instalacji i Użytkowania
Instalacja
Upewnij się, że pistolet jest rozładowany, a komora czysta.
Usuń fabryczną dźwignię zwolnienia zasuwy z karabinu DPMS LR308 lub kompatybilnego.
Wyreguluj przedłużone zwolnienie zasuwy EBRv2/308 w obszarze montażu.
Mocno przymocuj przedłużone zwolnienie zasuwy, upewniając się, że jest stabilnie na miejscu.
Przetestuj działanie dźwigni, aby potwierdzić prawidłową instalację.
Użytkowanie
Aby zablokować zamek w tylnym położeniu, naciśnij w górę na dźwigni używając palca wskazującego.
Aby zwolnić zamek, lekko naciśnij w dół na dźwigni, jednocześnie trzymając mocno uchwyt pistoletowy.
Ćwicz te operacje w bezpiecznym środowisku, aby zapoznać się z funkcjami.
Instrukcje Utylizacji
Utylizuj produkt zgodnie z lokalnymi przepisami dotyczącymi metali i komponentów broni palnej.
Nie wyrzucaj produktu do zwykłych odpadów domowych.
Rozważ opcje recyklingu dostępne w twoim rejonie, aby zminimalizować wpływ na środowisko.
Informacje Kontaktowe dla Dalszego Wsparcia
W przypadku pytań dotyczących bezpieczeństwa lub dodatkowego wsparcia, prosimy o zapoznanie się z oficjalną stroną internetową producenta lub zasobami obsługi klienta. Zawsze upewnij się, że masz najnowsze informacje dotyczące produktu i jego wytycznych bezpieczeństwa.
Dziękujemy za priorytetowe traktowanie bezpieczeństwa podczas korzystania z Przedłużonego Zwolnienia Zasuwnicy 308 AR V2. Twoje przestrzeganie tych wytycznych pomaga zapewnić bezpieczne doświadczenie strzeleckie dla ciebie i osób wokół ciebie.
Napotkaliśmy błąd podczas wczytywania tej zawartości. Odśwież stronę, aby kontynuować. Jeśli problem będzie się powtarzał, skontaktuj się z naszym działem obsługi klienta.
Elementy te są kontrolowane przez rząd USA i dopuszczone do eksportu tylko do kraju docelowego przeznaczenia do wykorzystania przez ostatecznego odbiorcę lub użytkowników końcowych określonych w niniejszym dokumencie. Nie można ich odsprzedawać, przekazywać ani w inny sposób rozdysponowywać do żadnego innego kraju ani do żadnej innej osoby niż upoważniony odbiorca końcowy lub użytkownik końcowy, w oryginalnej postaci lub po włączeniu do innych przedmiotów, bez uprzedniego uzyskanie zgody od rządu USA lub w inny sposób zatwierdzony przez prawo i przepisy USA.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Elementy te są kontrolowane przez rząd USA i dopuszczone do eksportu tylko do kraju docelowego przeznaczenia do wykorzystania przez ostatecznego odbiorcę lub użytkowników końcowych określonych w niniejszym dokumencie. Nie można ich odsprzedawać, przekazywać ani w inny sposób rozdysponowywać do żadnego innego kraju ani do żadnej innej osoby niż upoważniony odbiorca końcowy lub użytkownik końcowy, w oryginalnej postaci lub po włączeniu do innych przedmiotów, bez uprzedniego uzyskanie zgody od rządu USA lub w inny sposób zatwierdzony przez prawo i przepisy USA.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.