Stabilny montaż celownika do Mosin Nagant od EGW!
Montaż Mosin Nagant od EGW pozwala na usunięcie tylnej muszki i zainstalowanie bazy bez konieczności odlutowywania czegokolwiek. Jest to jedna z najbardziej stabilnych baz dostępnych na rynku, która wykorzystuje obudowę tylnej muszki, co oznacza, że nie są wymagane większe modyfikacje Twojej broni, jak w przypadku niektórych innych marek.
Instalacja:
- Usuń tylną muszkę z obudowy.
- Zachowaj oryginalny pin, ponieważ będzie potrzebny do instalacji bazy.
- Włóż stronę z zakładką naszej stalowej bazy do tylnej części obudowy muszki.
- Sprawdź dopasowanie z przodu stalowej bazy.
- Rogi i przód mogą wymagać przeszlifowania, aby uzyskać optymalne dopasowanie.
- Gdy baza całkowicie osadzi się w tylnej obudowie, włóż pin zabezpieczający z oryginalnej muszki.
- Dostosuj śrubę blokującą, aby wyeliminować luz na szynie.
- Przykręć górny aluminiowy montaż do stalowej bazy.
Ten montaż można zamontować w obu kierunkach. EGW zaleca zmierzenie odległości otworów w Twoim odbiorniku, aby potwierdzić, że odpowiada wymiarom opublikowanym przez nich.
Rowki Picatinny biegną na całej długości szyny, co daje strzelcowi elastyczność przy montażu pierścieni celowniczych i innych akcesoriów. Kanał w środku zmniejsza całkowitą masę montażu. W wielu przypadkach nie będzie również przeszkadzał w korzystaniu z fabrycznych celowników mechanicznych. Montaże celowników EGW w jednym kawałku są oczywistym wyborem zarówno dla myśliwych, jak i strzelców taktycznych.
EGW wytwarza te montaż w swoim warsztacie, korzystając z jednego ze swoich centrów obróbczych. Po obróbce montaż są polerowane, piaskowane i anodowane typem III, co zapewnia długotrwałą trwałość.
Rekomendacje dotyczące instalacji:
EGW zaleca moment obrotowy 20 cali funtów oraz kropelkę niebieskiego loctite (loctite sprzedawany jest osobno).
EGW's Mosin Nagant mount allows you to remove the rear leaf sight and install the base without the need to unsolder anything. It is one of the most stable bases on the market and uses the rear sight housing so there are no major modifications to your rifle like with some other brands. Installation: Remove rear leaf sight from the housing Keep the original pin as you will need this to install the base Insert the tabbed side of our steel base in to the rear of the rear sight Check for fitment on the front of the steel base The corners and front may need to be filed down to achieve the optimal fit Once the base sits completely in the rear housing insert the retaining pin from the original sight Adjust the set screw to take up any play in the rail Screw the top aluminum mount to the steel base This mount can be put on in either direction EGW recommends measuring the hole spacing in your receiver to confirm it matches with the dimensions they have published. Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The channel in the center reduces the overall mass of the mount. Also, in many cases, it will not obstruct usage of factory iron sights. EGW one-piece scope mounts are the obvious choice for hunters and tactical shooters alike. EGW machines these in thier shop using one of their machining centers. After machining, the mounts are tumbled, sand blasted, and Type III anodized for long lasting durability. Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is sold separately).