Stabilny montaż celownika do Mosina Naganta od EGW
Montaż EGW do Mosin Nagant pozwala na usunięcie tylnej muszki i zainstalowanie podstawy bez konieczności lutowania czegokolwiek. Jest to jedna z najstabilniejszych podstaw na rynku, która wykorzystuje obudowę tylnej muszki, więc nie wymaga dużych modyfikacji w Twojej broni, jak w przypadku niektórych innych marek.
Instalacja:
- Usuń tylną muszkę z obudowy.
- Zachowaj oryginalny pin, ponieważ będzie potrzebny do zainstalowania podstawy.
- Włóż stronę z zaczepem naszej stalowej podstawy do tyłu tylnej muszki.
- Sprawdź dopasowanie z przodu stalowej podstawy.
- Rogi i przód mogą wymagać oszlifowania, aby uzyskać optymalne dopasowanie.
- Gdy podstawa całkowicie leży w tylnej obudowie, włóż pin zatrzymujący z oryginalnej muszki.
- Dostosuj śrubę ustalającą, aby wyeliminować luz na szynie.
- Przykręć górny aluminiowy montaż do stalowej podstawy.
Ten montaż można zamontować w dowolnym kierunku. EGW zaleca zmierzenie odległości otworów w Twoim receiverze, aby potwierdzić, że pasuje do wymiarów, które opublikowali.
Rowki Picatinny biegną na całej długości szyny, co daje strzelcowi elastyczność przy montażu pierścieni celowniczych i innych akcesoriów. Kanał w środku zmniejsza całkowitą masę montażu. Ponadto w wielu przypadkach nie będzie on przeszkadzał w użytkowaniu fabrycznych przyrządów celowniczych. Montaży celowników EGW w jednym kawałku są oczywistym wyborem zarówno dla myśliwych, jak i strzelców taktycznych.
EGW produkuje te montaże w swoim warsztacie, korzystając z jednego ze swoich centrów obróbczych. Po obróbce, montaż jest poddawany procesowi tumblowania, piaskowania oraz anodowania typu III, co zapewnia długotrwałą trwałość.
Zalecenia dotyczące instalacji:
EGW zaleca moment obrotowy 20 cali funtów oraz kroplę niebieskiego loctite'a (loctite sprzedawany jest osobno).
EGW's Mosin Nagant mount allows you to remove the rear leaf sight and install the base without the need to unsolder anything. It is one of the most stable bases on the market and uses the rear sight housing so there are no major modifications to your rifle like with some other brands. Installation: Remove rear leaf sight from the housing Keep the original pin as you will need this to install the base Insert the tabbed side of our steel base in to the rear of the rear sight Check for fitment on the front of the steel base The corners and front may need to be filed down to achieve the optimal fit Once the base sits completely in the rear housing insert the retaining pin from the original sight Adjust the set screw to take up any play in the rail Screw the top aluminum mount to the steel base This mount can be put on in either direction EGW recommends measuring the hole spacing in your receiver to confirm it matches with the dimensions they have published. Picatinny cross slots run the full length of the rail, which gives the shooter flexibility when mounting scope rings and other accessories. The channel in the center reduces the overall mass of the mount. Also, in many cases, it will not obstruct usage of factory iron sights. EGW one-piece scope mounts are the obvious choice for hunters and tactical shooters alike. EGW machines these in thier shop using one of their machining centers. After machining, the mounts are tumbled, sand blasted, and Type III anodized for long lasting durability. Installation: EGW recommends 20 inch lbs of torque and a drip of blue loctite (loctite is sold separately).