Twój koszyk jest pusty.

Koszyk

VLTOR WEAPON SYSTEMS
AR-15 GAS BLOCK LOW PROFILE

100003996

Jednoczęściowa konstrukcja pasuje pod wolnopodwieszane osłony rąk

Smukła alternatywa dla nieporęcznej wieży celowniczej USGI/frontowego bloku gazowego charakteryzuje się niskim profilem, co przekłada się na bardziej zwarty wygląd i mniejsze ryzyko zaczepienia o roślinność czy inne wyposażenie. Zakrywa tylko 1" długości lufy i zmniejsza ciężar broni z przodu, co poprawia obsługę i manewrowość. Modele Clamp On obejmują lufę za pomocą dołączonych śrub imbusowych. Modele Set Screw wykorzystują dołączone śruby ustalające na spodzie jednostki, aby zakotwiczyć blok gazowy do lufy, zapewniając instalację o najniższym profilu.

Więcej...

One-Piece Design Fits Under Free-Float Handguards

Slim replacement for cumbersome USGI front sight/gas block tower features a low profile for a more streamlined appearance and less chance of snagging on vegetation and other gear. Covers only 1" of barrel length and reduces weapon’s forward weight for improved handling and maneuverability. Clamp On models squeeze around the barrel with included socket head screws. Set Screw models use included set screws at the bottom of the unit to anchor the gas block to the barrel for the lowest-profile installation.

Więcej...

Oceny klientów dla VLTOR WEAPON SYSTEMS AR-15 GAS BLOCK LOW PROFILE .750 STEEL BLACK

Liczba ocen: 12
Od brownells.com: 12
Średnia ocena: 4,1

Poor Quality Set Screws (12-02-2015)

I have a VLTOR one piece upper so I thought this would be a good match. The gas block itself looks good. Unfortunately, one of the set screws stripped when I applied minimal torque with an Allen (hex) key. The other set screw was fine. I'm not sure if this was an isolated defect, but I ended up having to drill one of the set screws out. This is very disappointing considering the slightly higher cost of the VLTOR block. To their credit Brownells' did accept this as a return.

Precision at it's Best (24-08-2015)

I compared this block first hand with seven other blocks before deciding to install the VLTOR block. The finish is superior to most; deep black phosphate and very uniform. The finish is equal to two other excellent choices, the Brownell's branded block and the Bravo Company block. The vertical grooves machined into the block add a pleasing and distinctive look and theoretically may offer some additional surface area for cooling. The machining appears very precise. Installation was straight forward and fit was tight and precise.

Nice gas block (12-07-2014)

This is a nicely done gas block but it touches my handguard (MI Gen 2 SS) very slightly at the screw heads. It is barely touching and I have checked that it is not canted, etc. Disappointing, but I will use it for another build I have planned. I usually prefer clamp on attachment, but the BCM barrel came with a dimple under the gas port so the set screw block I am replacing this with should work fine. A little filing would fix the issue, but I would rather not have to.

Less than useful (14-06-2010)

The fact the screws are on the side should have been screaming at me. It is not low profile at all, the screws protrude so far when mounted it was impossible to fit under the DD 10" Lite rail. The screws do not recess enough for proper clearance. The other version I have seen of this would fit fine as the screws are recessed and are on the bottom.

No problems (19-06-2010)

I have this installed on my SPR build which has a
White Oak Armament barrel with Midwest Industries free float handguards and everything works perfectly. My rifle cycles correctly and the bolts for the gas block has not come loose. I did however use vibra-lock on the threads.

Perfect! (07-07-2010)

After having a nasty experience with the "set screw style" gas block I decided to use a clamp on and went with the Vltor. This gas block is very well made. It was a bit tight for the gas tube to fit in which is normal and once the tube was in everything with very smoothly. Make sure to loctite the screws and this thing wil stay forever. I put this underneath my TRX Extreme which is extremely skinny. This will fit under most handguards. I don't believe this gas block is made to fit under the DD Lites and Omegas, and also the LaRues. For the handguards it is made to fit under, I'd prefer no other.

Great Low-Pro Steel Gas Block (16-01-2011)

I used this on a 16" Mid-Length Gas System AA 6.5 Grendel barrel. I have fired it in both extreme heat at 100 degrees F, down to 18 degrees F with never a malfunction using various loads. This is one of the best steel low-pro gas blocks on the market. The gas tube does fit tightly, which is a good thing for a reliable gas circuit. Loc-tite is your friend when tightening the screws after testing that you have a proper gas circuit. Read the limitations as to what handguards it will not fit under. The finish and logo are features that go above what other manufacturers offer on most of these types of products, which shows that VLTOR goes further in making a great part. Every VLTOR product I have used so far shows a higher attention to workmanship, finish, and functionality.

Super nice fit on Black Hole Weap bbl (10-08-2011)

I installed this VLTOR low profile, side clamping, gas block on a standard profile, stainless, 24 inch long, 6.8mm SPC, Black Hole Weaponry barrel. The fit was nice and snug even before I tightened the bolts. It stayed aligned while tightening. I then fit a rifle length gas tube and covered the whole set-up with a Midwest Ind. SS, 15 inch free floating hand-guard. This gas block fit underneath just fine. It fired and cycled from round one and I now have 300 rounds through the rifle without a single problem. No leaks of any gas. Alex Clark Homer, Alaska

Fits like a glove (12-08-2011)

I installed this gas block on a 0.75 inch diameter Black Hole weaponry barrel. It fit nice and snug.
The gas tube hole was nice and snug as well. After tightening I attempted to whack the gas block with a mallet to see if it would move. It did not. Now after 300 hot experimental hand-loads there is NO gas leakage. This gas block fit under a Midwest Industries SS type extended hand-guard without touching.

nice product (26-08-2011)

well made quality product. small, compact, fits right.

great piece (03-11-2013)

High value installs easy and worth every penny!

Solid but Flawed (24-08-2016)

Technically there's nothing wrong with this product. It's a solid, tightly-clamping, beautifully-fitting, streamlined gas block. The one enormous problem is that the standard hex screws it uses still have full-sized heads, heads which are (at least seemingly) in direct, if glancing, contact with the inside of my Midwest Industries MLOK guard. Now this pretty well eliminates any chance of the screws walking loose, but it also threatens the free-float nature of the guard. I so far haven't noticed an effect on accuracy, but I only run a red dot. And in addition to the 6 o'clock rail slot (or half of two of them on mine) being blocked by the bottom portion as is typical, the 4:30 and 3 o'clock slots are also unusable now on account of the screws. Lacking grip panels to guard against heat buildup, the middle 20 percent of my 15" rail is ungrip-able because of this gap. Still, if your technique allows for this or you just want a good, solid clamp design, you could definitely do worse.

Zobacz 12 dodatkowych opinii na brownells.com

499 499 1 PLN

Nr produktu: 100003996
VLTOR WEAPON SYSTEMS AR-15 GAS BLOCK LOW PROFILE .750 STEEL BLACK
Numer części: GB2C Smukła alternatywa dla nieporęcznej wieży celowniczej USGI/frontowego bloku gazowego charakteryzuje się niskim profilem, co przekłada się na bardziej zwarty wygląd i mniejsze ryzyko zaczepienia o roślinność czy inne wyposażenie. Zakrywa tylko 1" długości lufy i zmniejsza ciężar broni z przodu, co poprawia obsługę i manewrowość. Modele Clamp On obejmują lufę za pomocą dołączonych śrub imbusowych. Modele Set Screw wykorzystują dołączone śruby ustalające na spodzie jednostki, aby zakotwiczyć blok gazowy do lufy, zapewniając instalację o najniższym profilu.

499 PLN 2 499,00 zł *

Czas dostawy ok. 14-21 dni.
2 szt. w magazynie w USA

Specyfikacja: Inside Diameter: .750 Make: AR-15 Material: Steel Style: Low-Profile, Clamp

Dodaj do listy zakupów

Zapytaj

Szczegóły

Dodaj do listy zakupów

Zapytaj

Cechy

Materiał: Steel Styl: Clamp,Low-Profile Wytwórca: AR-15 Średnica wewnętrzna: .750 Waga dostawy: 0,045kg Wysokość wysyłki: 20mm Szerokość wysyłki: 84mm Długość wysyłki: 183mm

Szczegóły pozycji

Made in USA
US export classification: 0A501.x

Jednoczęściowa konstrukcja pasuje pod wolnopodwieszane osłony rąk

Więcej...

One-Piece Design Fits Under Free-Float Handguards

Więcej...

Oceny klientów dla VLTOR WEAPON SYSTEMS AR-15 GAS BLOCK LOW PROFILE .750 STEEL BLACK

Liczba ocen: 12
Od brownells.com: 12
Średnia ocena: 4,1

Poor Quality Set Screws (12-02-2015)

Precision at it's Best (24-08-2015)

Nice gas block (12-07-2014)

Less than useful (14-06-2010)

No problems (19-06-2010)

Perfect! (07-07-2010)

Great Low-Pro Steel Gas Block (16-01-2011)

Super nice fit on Black Hole Weap bbl (10-08-2011)

Fits like a glove (12-08-2011)

nice product (26-08-2011)

well made quality product. small, compact, fits right.

great piece (03-11-2013)

High value installs easy and worth every penny!

Solid but Flawed (24-08-2016)

Zobacz 12 dodatkowych opinii na brownells.com

Sugerowane pozycje
Pozycje alternatywne

DOUBLE STAR .750" PICATINNY GAS BLOCK
AR-15/M16 PICATINNY RAIL GAS BLOCK

DOUBLE STAR

W magazynie

249,00 zł *

Bloki gazowe

3,4

KINETIC RESEARCH GROUP BRAVO HOOK-STYLE COVER FDE
BRAVO CHASSIS HOOK-STYLE COVER

KINETIC RESEARCH GROUP

W magazynie

119,00 zł *

CMMG AR15 8.2" 300BLK MR BARREL
AR-15/M16 300 BLK BARRELS

CMMG

W magazynie

1 249,00 zł * 1 249,00 zł - 1 419,00 zł*

Lufy karabinowe

3,6

CMMG PS90 10.4 BARREL 4150CMV CL 1:9 5.7X28
PS90 10.4" BARREL

CMMG

W magazynie

1 999,00 zł *

Lufy karabinowe

Zaloguj się

Nie pamiętasz hasła?
Zarejestruj się

Kontakt

Facebook

Mapa strony

Kategorie produktów

Zamawianie

Obsługa klienta

Witamy!

Witamy w brownells.pl wiodącym dostawcy w Polsce akcesoriów do broni, części broni, narzędzi rusznikarskich, narzędzi do elaboracji amunicji oraz komponentów.

Co oferujemy

Lubisz strzelać, pracujesz przy naprawach broni zawodowo lub hobbystycznie lub po prostu jesteś właścicielem broni, to nasza strona jest właśnie dla Ciebie!

Przez ponad 75 lat strzelcy, rusznikarze, hobbyści, wojskowi, służby specjalne korzystają z usług Brownells jako dostawcy szerokiego asortymentu, wysokiej jakości części broni. Znajdziesz ponad 90 000 produktów w tym części nietypowe, akcesoria, narzędzia rusznikarskie i inne produkty do utrzymania, naprawy i ulepszania swojej broni.

Ceny zawierają VAT, bez kosztu wysyłki

Widok klasyczny

Widok mobilny