Twój koszyk jest pusty.

Koszyk

Newsletter

BROWNELLS
79° MUZZLE CROWNING CUTTER

080586500

Cięcia popularnych "11\" Target korony

Stali hartowanej, kaganiec ukoronowaniem cięcie narzędzie niewielkie (11° mniej niż kwadrat) cel fazowania na beczki. Daje dobry gwintowanie ochrony bez wchodzenia zbyt głęboko. 90-11 = 79 °, stąd nazwa. Osiem, precyzyjnie flety daje gładkie, bez gadania kawałki aby pomóc wyeliminować dodatkowe docierania lub ukamienowanie. gwint ¼"-20 pasuje Brownells kaganiec uchwyty fazowania. Korzystać z naszych pilotów kaganiec aby zapewnić precyzyjne wyrównanie z twój otwór. Dostępne w średnicach ½" i ¾", aby pomieścić większość o średnicy lufy karabin/pistolet.

Dane techniczne: stal narzędziowa, 23/8"(6cm) Długość całkowita, ½" (1,3 cm) lub ¾"(1,9 cm) od ¼"-20 tpi.

Więcej...

Cuts Popular "11\" Target Crown

Hardened steel, muzzle crowning tool cuts a slight (11° less than square) target chamfer on barrels. Gives good rifling protection without going too deep. 90° - 11° = 79°, hence the name. Eight, precision-machined flutes give smooth, chatter-free cuts to help eliminate extra lapping or stoning. ¼"-20 thread fits Brownells muzzle chamfering handles. Use with our muzzle pilots to ensure precise alignment with your bore. Available in ½" and ¾" diameters to accommodate most rifle/handgun barrel diameters.

SPECS: Tool Steel, 23/8” (6cm) overall length, ½" (1.3cm) or ¾" (1.9cm) O.D. ¼"-20 tpi.

Więcej...

Oceny klientów dla BROWNELLS 1/2" 79° CROWN CUTTER

Liczba ocen: 15
Od brownells.com: 15
Średnia ocena: 4,8

A must have! (24-09-2009)

I have shortened many barrels lately on Ruger Single Actions along with a few rifles. I will never go back to the file and stones mounted in drills. Very easy to use and gives a nice final touch.

Just what the doctor ordered!! (12-02-2010)

i originally bought this to do the crown on a savage 12bvss in 223 that wouldn't quite do 1/2 minute groups.i notice the factory crown looked a little rough and failed the q-tip test miserably . this tool made quick work of the factory crown . was a little worried at first because of the step in the factory crown . but with nothing but a drill an Brownells drill chuck adapter i was able to cut the factory crown down quickly and with absolutely no chatter marks . after the recrown the savage went from a .6 to .8 minute rifle to a .25 - .3 rifle . so i decided to use it on all of my rifles . this is one fine dandy of a tool that is easy to use and works better than i expected!!

Easy to get perfect crown. (26-10-2010)

Easy to use with perfect results. I needed to repair a Ruger 77/44 damaged grown.
First time for me,and took just 15 min. Results proved it self at the range,no more flyers.

A solid tool (02-02-2011)

This is a solid built tool that does a nice job on my Mauser barrel. I was disapointed that it did not come with any directions about barrel crowning. Had to go online to find out how to use it correctly.

Easy crowning tool (18-02-2011)

I use it to do quick touch-ups to dinged muzzles and also when cutting and crowning. Works good and fast with good results.

Colt 32 Hammerless (09-12-2011)

When I bought the pistol bubba had made contact with the crown and you could not shoot it. 20 minutes after using the cutter it was as good as new - maybe better.

this product is well worth the money (12-02-2012)

worked great i had to cut down the barrel of a 300wsm had no proublem using it my cut with a hack saw was not streight so i used a gun grease on the brrel and pilot catches the bigger chips then when it was streight i switched to motor oil it holds the smaller chips better then cutting oil i think so any way just go slow and clean the chips out of the cutter with a tooth brush very ofter go slow and you will have no proulem i would use the brass pilot becaue you will get chips in the barrel and better they nick it up then your rifling then i used a brass acorn nut and cut off a bolt and put it in my drill with ploishing compond to finish to finish the crown the gun shoots great

Used this for Mosin Nagant Rifles (10-08-2013)

I ordered this to use on my Mosin Nagant Rifles. One was a Type 53 carbine with a dinged up crown. The other Mosin was a project 91/30 rifle. I cut the barrel back to 22", squared and cleaned up the crown with hand files and varying degrees of sand paper and finished it off with this crowning cutter.

The 3/4" size was perfect for both rifles, although I had to order the .30 and .311 steel pilots due to differences in both sizes of the bores to avoid a wobbling pilot when cutting. I also ordered the handle to fit the cutter.

I checked out several internet videos to see how to properly use the cutter, chose the correct size pilot, secured it with the set screw and used plenty of oil. I went slow using hand pressure only turning to the right. I stopped every once in a while to brush off the metal chips. It provided a very uniform crown. I cleaned up the crown with some 600 grain wet/dry sand paper.

I am not a gunsmith but I do occasional small projects to my firearms. I was hesitant to do this job myself but it is real easy and anyone with some mechanical ability could use it. It payed for itself the first time I used it and saved me money the second time versus taking to the local gunsmith, paying him and having the firearms gone for several weeks.

it works (20-02-2014)

I recut the crown on an antique Spencer .50. The 501 brass guide fit perfectly. I used my cordless drill slowly. clean often...chatters a little.
doughnut shaped 300 then 400 grit on the end of the cutter smoothed everything off. under 2" 50 yard groups now from a 149 year old carbine. 20 mnutes work and done....
perfect! highly recommended for home gunsmith.

New life to old rifles (14-12-2017)

This was the easiest gunsmithing project I have done to date. I own a few old Mosin-Nagant's and I needed to re-crown a couple of them and I was dreading doing this job because I thought it was going to be too hard and I'll screw something up. Nope, it only took 20 minutes per rifle and it was super easy with the correct pilot. I got both the .30 and .303 British pilots just in case and so far have only used the .30. I made the mistake, one time, of forgetting to add cutting oil to the bit between cuts. Good cutting oil makes a big difference to the ease of cutting.

<img width="500" src='/userdocs/reviewimages/9e27ee24-f311-4ae0-8d58-4e49fb4d1c53.jpg' alt=''>

Good quality product. (08-11-2009)

The cutter has the look of qood quality. It cuts real smooth and stays sharp for a long time.

Easy Target Crown (18-03-2010)

Very High Quality tool, cuts a great crown and leaves a very nice finish. Use plenty of cutting oil and clean chips often and this tool will give you great results.

Works well. (04-11-2011)

This cutter works pretty well. It takes a little practice getting the feel for using the correct amount of pressure so as not to leave chatter marks. Use lots of cutting fluid, such as Do Drill. It might work even better if the cutting surfaces were staggered.

good tool (01-12-2012)

i used this tool to recrown a 25-06 bought the .257 brass guide to go with it turned it by hand stopping often to clean shavings with tooth brush used motor oil to keep lubricated took about 30 minutes cut aperfect crown very satisfied!!!!!

Only crown tool I've used but it worked (03-03-2013)

I did not use the T handle you have to purchase separately with this product I simply threaded a nut on the end I had laying around and utilized a ratcheting wrench. This product cuts very well and evenly. With the .30 cal pilot and some motor oil, I was able to crown my barrel very well. What I didn't like is that though my .30 cal pilot worked, it seemed to fit slightly loose. That could also be normal. Overall this tool worked well.

Zobacz 15 dodatkowych opinii na brownells.com

344 374 2 PLN

Nr produktu: 080586500
BROWNELLS 1/2" 79° CROWN CUTTER
Numer części: 800005000020 Stali hartowanej, kaganiec ukoronowaniem cięcie narzędzie niewielkie (11° mniej niż kwadrat) cel fazowania na beczki. Daje dobry gwintowanie ochrony bez wchodzenia zbyt głęboko. 90-11 = 79 °, stąd nazwa. Osiem, precyzyjnie flety daje gładkie, bez gadania kawałki aby pomóc wyeliminować dodatkowe docierania lub ukamienowanie. gwint ¼"-20 pasuje Brownells kaganiec uchwyty fazowania. Korzystać z naszych pilotów kaganiec aby zapewnić precyzyjne wyrównanie z twój otwór. Dostępne w średnicach ½" i ¾", aby pomieścić większość o średnicy lufy karabin/pistolet.

344 PLN 107 344,00 zł *

W magazynie w USA - dostawa 9 - 19 dni roboczych

Dodaj do listy zakupów

Zapytaj

Szczegóły

Dodaj do listy zakupów

Zapytaj

Cechy

Waga dostawy: 0,023kg Wysokość: 15mm Szerokość: 33mm Długość: 145mm

Szczegóły pozycji

Made in USA

Nr produktu: 080586750
BROWNELLS 3/4" 79 CROWN CUTTER Stali hartowanej, kaganiec ukoronowaniem cięcie narzędzie niewielkie (11° mniej niż kwadrat) cel fazowania na beczki. Daje dobry gwintowanie ochrony bez wchodzenia zbyt głęboko. 90-11 = 79 °, stąd nazwa. Osiem, precyzyjnie flety daje gładkie, bez gadania kawałki aby pomóc wyeliminować dodatkowe docierania lub ukamienowanie. gwint ¼"-20 pasuje Brownells kaganiec uchwyty fazowania. Korzystać z naszych pilotów kaganiec aby zapewnić precyzyjne wyrównanie z twój otwór. Dostępne w średnicach ½" i ¾", aby pomieścić większość o średnicy lufy karabin/pistolet.

374 PLN 27 374,00 zł *

W magazynie w USA - dostawa 9 - 19 dni roboczych

Dodaj do listy zakupów

Zapytaj

Szczegóły

Dodaj do listy zakupów

Zapytaj

Cięcia popularnych "11\" Target korony

Dane techniczne: stal narzędziowa, 23/8"(6cm) Długość całkowita, ½" (1,3 cm) lub ¾"(1,9 cm) od ¼"-20 tpi.

Więcej...

Cuts Popular "11\" Target Crown

SPECS: Tool Steel, 23/8” (6cm) overall length, ½" (1.3cm) or ¾" (1.9cm) O.D. ¼"-20 tpi.

Więcej...

Oceny klientów dla BROWNELLS 1/2" 79° CROWN CUTTER

Liczba ocen: 15
Od brownells.com: 15
Średnia ocena: 4,8

A must have! (24-09-2009)

I have shortened many barrels lately on Ruger Single Actions along with a few rifles. I will never go back to the file and stones mounted in drills. Very easy to use and gives a nice final touch.

Just what the doctor ordered!! (12-02-2010)

Easy to get perfect crown. (26-10-2010)

Easy to use with perfect results. I needed to repair a Ruger 77/44 damaged grown.
First time for me,and took just 15 min. Results proved it self at the range,no more flyers.

A solid tool (02-02-2011)

Easy crowning tool (18-02-2011)

I use it to do quick touch-ups to dinged muzzles and also when cutting and crowning. Works good and fast with good results.

Colt 32 Hammerless (09-12-2011)

When I bought the pistol bubba had made contact with the crown and you could not shoot it. 20 minutes after using the cutter it was as good as new - maybe better.

this product is well worth the money (12-02-2012)

Used this for Mosin Nagant Rifles (10-08-2013)

it works (20-02-2014)

New life to old rifles (14-12-2017)

Good quality product. (08-11-2009)

The cutter has the look of qood quality. It cuts real smooth and stays sharp for a long time.

Easy Target Crown (18-03-2010)

Very High Quality tool, cuts a great crown and leaves a very nice finish. Use plenty of cutting oil and clean chips often and this tool will give you great results.

Works well. (04-11-2011)

good tool (01-12-2012)

Only crown tool I've used but it worked (03-03-2013)

Zobacz 15 dodatkowych opinii na brownells.com

Sugerowane pozycje
Klienci kupili także

CRATEX COARSE, #11 BULLET, 1/8" ARBOR
REPLACEMENT BULLET POINTS

CRATEX

Dostępne W magazynie w USA - dostawa 9 - 19 dni roboczych

469,00 zł * 304,00 zł - 599,00 zł*

Gumowe narzędzia ścierne ostrołukowe

5 (1)

EGW CARBIDE REVERSE PLUG REAMER
1911 COLLAR REVERSE PLUG REAMER

EGW

Dostępne W magazynie w USA - dostawa 9 - 19 dni roboczych

819,00 zł * 679,00 zł - 819,00 zł*

Rozwiertaki

1 (1)

REAL AVID ACCU-PUNCH HAMMER & ROLL PIN PUNCH SET
ACCU-PUNCH HAMMER & ROLL PIN PUNCH SET

REAL AVID

W magazynie w USA - dostawa 9 - 19 dni roboczych W magazynie w USA - dostawa 9 - 19 dni roboczych

354,00 zł *

Wybijaki

0 (0)

FORSTER MAUSER (1/4"-22) GUIDE SCREWS 2-PACK
INLETTING GUIDE SCREWS

FORSTER

Dostępne W magazynie w USA - dostawa 9 - 19 dni roboczych

79,00 zł * 79,00 zł - 89,00 zł*

Śruby do przymierzania osady

3 (1)

Zaloguj się

Nie pamiętasz hasła?
Zarejestruj się

Kontakt

Facebook

Mapa strony

Kategorie produktów

Zamawianie

Obsługa klienta

Witamy!

Witamy w brownells.pl wiodącym dostawcy w Polsce akcesoriów do broni, części broni, narzędzi rusznikarskich, narzędzi do elaboracji amunicji oraz komponentów.

Co oferujemy

Lubisz strzelać, pracujesz przy naprawach broni zawodowo lub hobbystycznie lub po prostu jesteś właścicielem broni, to nasza strona jest właśnie dla Ciebie!

Przez ponad 75 lat strzelcy, rusznikarze, hobbyści, wojskowi, służby specjalne korzystają z usług Brownells jako dostawcy szerokiego asortymentu, wysokiej jakości części broni. Znajdziesz ponad 90 000 produktów w tym części nietypowe, akcesoria, narzędzia rusznikarskie i inne produkty do utrzymania, naprawy i ulepszania swojej broni.