Wysokiej jakości mocowanie do celownika Trijicon RMR dla modeli S&W M&P
Przedstawiamy mocowanie S&W M&P TRIJICON RMR SIGHT MOUNT od marki EGW, które zapewnia solidne i niezawodne wsparcie dla Twojego celownika red dot.
Opis produktu:
- Materiał: Aluminium 7075
- Powłoka: Matowa czarna powłoka twarda
- Całkowita długość: 1.780"
- Całkowita szerokość: 1.1"
- Elementy montażowe: (2) śruby flat head 6-32, (1) śruba 6-32 x 3/16
- Dopasowanie red dot: Trijicon RMR
To mocowanie pasuje do:
- Smith & Wesson M&P Full Size
- Smith & Wesson M&P 2.0 Full Size
- Smith & Wesson M&P 22 Full Size
- Smith & Wesson M&P Compact*
- Smith & Wesson M&P 2.0 Compact*
- Smith & Wesson SD9VE
- Smith & Wesson SD40VE
To mocowanie nie pasuje do:
- Smith & Wesson M&P Shield (Nasze mocowanie jest zbyt szerokie, aby pasować do Shield)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE
- Smith & Wesson M&P C.O.R.E Series
*Nie będzie pasować do M&P .22 Compact.
Tylny szynowy system celownika Smith and Wesson może różnić się wymiarami. Nasze celowniki są wykonane z zachowaniem tych samych tolerancji. Niektórzy użytkownicy mogą mieć trudności z zainstalowaniem naszej płyty na ich zamku z powodu różniących się tolerancji. Prosimy o uwzględnienie tego podczas składania zamówienia.
Te mocowania powinny być instalowane i sprawdzane przez wykwalifikowanego rusznikarza. Nie ponosimy odpowiedzialności za szkody lub obrażenia, które mogą wyniknąć z niewłaściwego montażu lub użytkowania tego produktu.
Instrukcje instalacji:
- Usuń tylny celownik*
- Zainstaluj mocowanie EGW w rowku szynowym
- Dokładnie dokręć śrubę ustalającą (jeśli dotyczy)
- Umieść celownik red dot na mocowaniu EGW (umieszczenie małego kawałka papieru między celownikiem a mocowaniem ułatwi demontaż i zabezpieczy Loctite przed dostaniem się na celownik).
- Nałóż niebieski Loctite na dostarczone śruby montażowe
- Dokręć śruby montażowe do 15 in/lbs
*Zalecane jest użycie narzędzia do pchania tylnego celownika.
Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780 Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR This mount will fit: Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact* Smith & Wesson M&P 2.0 Compact* Smith & Wesson SD9VE Smith & Wesson SD40VE This mount does not fit: Smith & Wesson M&P Shield (Our mount is too wide to fit the Shield) Smith & Wesson M&P Shield EZ .380 Smith & Wesson SW9VE Smith & Wesson SW40VE Smith & Wesson M&P C.O.R.E Series *Will not fit the M&P .22 Compact. Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering.These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended*