Aby zamontować celownik Vortex Razor, C-More RTS lub STS, wystarczy usunąć tylny przyrząd celowniczy z broni i zastąpić go montażem EGW. Montaż można w każdej chwili zdjąć i ponownie zamontować tylny przyrząd celowniczy. W zestawie znajduje się niezbędne okucie montażowe. Instrukcja instalacji: Usuń tylny przyrząd celowniczy* Zainstaluj montaż EGW w rowku Zaciśnij śrubę ustalającą (jeśli dotyczy) Umieść celownik kolimatorowy na montażu EGW (umieszczenie małego kawałka papieru między celownikiem kolimatorowym a montażem ułatwi późniejsze usunięcie i ochroni przed dostaniem się Loctite na celownik kolimatorowy) Nałóż niebieski Loctite na dostarczone śruby montażowe Dokręć śruby montażowe momentem 15in/lbs Śruby dołączone do tego montażu wymagają klucza imbusowego 5/64'' do instalacji. Ten montaż pasuje do: Rewolwerów Smith & Wesson K Frame Rewolwerów Smith & Wesson L Frame Rewolwerów Smith & Wesson N Frame Rewolwerów Smith & Wesson X Frame Jeśli Twój rewolwer nie jest fabrycznie przewiercony i gwintowany, ten montaż nie będzie pasował. Najlepszym sposobem na sprawdzenie, czy broń jest przewiercona i gwintowana jest otwarcie bębna i sprawdzenie belki pod nim. Powinny być tam otwory przelotowe, które są przewiercone i gwintowane. Jeśli ich nie ma (jak na powyższym obrazku), montaż nie będzie pasował bez przewiercenia i gwintowania broni. Możesz zlecić kompetentnemu i wykwalifikowanemu rusznikarzowi przewiercenie i gwintowanie górnej części broni zgodnie ze standardowym wzorem otworów S&W, co umożliwi użycie naszego montażu.
Więcej...
Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: Smith & Wesson K Frame Revolvers Smith & Wesson L Frame Revolvers Smith & Wesson N Frame Revolvers Smith & Wesson X Frame Revolvers If your revolver is not drilled and tapped this mount will not work. The best way to verify that it is/is not drilled and tapped is to open the cylinder and check the rib underneath. There should be through holes that are drilled and tapped. If there are not (like the above image) this mount will not work without you having the gun drilled and tapped. You can have a competent and qualified gunsmith drill and tap the top strap with the standard S&W hole pattern which will allow you to use our mount.
Więcej...
3443441PLN
Nr produktu: 296000691 EGW S&W K, L, N, X FRAME VORTEX RAZOR SIGHT MOUNT Numer części: 49438841370113019 Aby zamontować celownik Vortex Razor, C-More RTS lub STS, wystarczy usunąć tylny przyrząd celowniczy z broni i zastąpić go montażem EGW. Montaż można w każdej chwili zdjąć i ponownie zamontować tylny przyrząd celowniczy. W zestawie znajduje się niezbędne okucie montażowe. Instrukcja instalacji: Usuń tylny przyrząd celowniczy* Zainstaluj montaż EGW w rowku Zaciśnij śrubę ustalającą (jeśli dotyczy) Umieść celownik kolimatorowy na montażu EGW (umieszczenie małego kawałka papieru między celownikiem kolimatorowym a montażem ułatwi późniejsze usunięcie i ochroni przed dostaniem się Loctite na celownik kolimatorowy) Nałóż niebieski Loctite na dostarczone śruby montażowe Dokręć śruby montażowe momentem 15in/lbs Śruby dołączone do tego montażu wymagają klucza imbusowego 5/64'' do instalacji. Ten montaż pasuje do: Rewolwerów Smith & Wesson K Frame Rewolwerów Smith & Wesson L Frame Rewolwerów Smith & Wesson N Frame Rewolwerów Smith & Wesson X Frame Jeśli Twój rewolwer nie jest fabrycznie przewiercony i gwintowany, ten montaż nie będzie pasował. Najlepszym sposobem na sprawdzenie, czy broń jest przewiercona i gwintowana jest otwarcie bębna i sprawdzenie belki pod nim. Powinny być tam otwory przelotowe, które są przewiercone i gwintowane. Jeśli ich nie ma (jak na powyższym obrazku), montaż nie będzie pasował bez przewiercenia i gwintowania broni. Możesz zlecić kompetentnemu i wykwalifikowanemu rusznikarzowi przewiercenie i gwintowanie górnej części broni zgodnie ze standardowym wzorem otworów S&W, co umożliwi użycie naszego montażu.
344PLN1344,00 zł
*
Czas dostawy ok. 14-21 dni. 1 szt. w magazynie w USA
Specyfikacja:Color: BlackMake: Smith & WessonMaterial: AluminumModel: K Frame, L Frame, N Frame, X FrameNumber of Bases: 1-PieceStyle: Tactical
Aby zamontować celownik Vortex Razor, C-More RTS lub STS, wystarczy usunąć tylny przyrząd celowniczy z broni i zastąpić go montażem EGW. Montaż można w każdej chwili zdjąć i ponownie zamontować tylny przyrząd celowniczy. W zestawie znajduje się niezbędne okucie montażowe. Instrukcja instalacji: Usuń tylny przyrząd celowniczy* Zainstaluj montaż EGW w rowku Zaciśnij śrubę ustalającą (jeśli dotyczy) Umieść celownik kolimatorowy na montażu EGW (umieszczenie małego kawałka papieru między celownikiem kolimatorowym a montażem ułatwi późniejsze usunięcie i ochroni przed dostaniem się Loctite na celownik kolimatorowy) Nałóż niebieski Loctite na dostarczone śruby montażowe Dokręć śruby montażowe momentem 15in/lbs Śruby dołączone do tego montażu wymagają klucza imbusowego 5/64'' do instalacji. Ten montaż pasuje do: Rewolwerów Smith & Wesson K Frame Rewolwerów Smith & Wesson L Frame Rewolwerów Smith & Wesson N Frame Rewolwerów Smith & Wesson X Frame Jeśli Twój rewolwer nie jest fabrycznie przewiercony i gwintowany, ten montaż nie będzie pasował. Najlepszym sposobem na sprawdzenie, czy broń jest przewiercona i gwintowana jest otwarcie bębna i sprawdzenie belki pod nim. Powinny być tam otwory przelotowe, które są przewiercone i gwintowane. Jeśli ich nie ma (jak na powyższym obrazku), montaż nie będzie pasował bez przewiercenia i gwintowania broni. Możesz zlecić kompetentnemu i wykwalifikowanemu rusznikarzowi przewiercenie i gwintowanie górnej części broni zgodnie ze standardowym wzorem otworów S&W, co umożliwi użycie naszego montażu.
Więcej...
Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Razor, C-More RTS or STS red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation. This mount fits: Smith & Wesson K Frame Revolvers Smith & Wesson L Frame Revolvers Smith & Wesson N Frame Revolvers Smith & Wesson X Frame Revolvers If your revolver is not drilled and tapped this mount will not work. The best way to verify that it is/is not drilled and tapped is to open the cylinder and check the rib underneath. There should be through holes that are drilled and tapped. If there are not (like the above image) this mount will not work without you having the gun drilled and tapped. You can have a competent and qualified gunsmith drill and tap the top strap with the standard S&W hole pattern which will allow you to use our mount.