Dla precyzyjnego wyrównywania podczas znakowania luf
Precyzyjnie wyrównuje indywidualne stemple stalowe, co pomaga zapewnić, że znaki są proste i równomiernie rozmieszczone podczas stemplowania oznaczeń kalibru na lufach. Śruby z łbem imbusowym pozwalają na regulację odległości między znakami, dzięki czemu osiągasz naprawdę profesjonalne rezultaty. Wyfrezowany otwór zapewnia niezakłócony widok na pierwszą głowicę stempla, co umożliwia prawidłowe ustawienie na elemencie roboczym przed uderzeniem młotkiem. Pasuje do stempli kwadratowych ¼" z rozmiarami znaków 1/16", 3/32" lub 1/8". Pasuje do luf o średnicy do 1-3/8".
SPECS: Aluminium, naturalne wykończenie z stalowym U-boltem i okuciami. Długość 2-3⁄8" (6 cm) x szerokość 3¼ (8,2 cm), wysokość 1½ (3,8 cm).
Więcej...
For Precision Alignment When Marking Barrels
Precisely aligns individual steel stamps to help ensure characters are straight and evenly spaced when stamping caliber designations on barrels. Allen head screws allow adjustment for accurate character spacing, so you get truly professional looking results. Machined port allows an unobstructed view of the first stamp head to ensure correct positioning on workpiece prior to tapping with your hammer. Accepts ¼" square stamps with 1/16", 3/32", or 1/8" character sizes. Fits barrels up to 1-3/8" diameter.
SPECS: Aluminum, natural finish with steel U-bolt and hardware. 2-3⁄8" (6cm) long x 3¼ (8.2cm) wide, 1½ (3.8cm) high.
Więcej...
Oceny klientów dla LA BOUNTY STEEL STAMP GUIDE
Liczba ocen: 2
Od brownells.com: 2
Średnia ocena: 1
Caution(08-01-2010)
The device is well made, however it will slip resulting in uneven markings. After reading the instructions over several times I tried it. I was disappointed with the results. I then tried it again on an old barrel and the same thing happened again. I made sure the holding ring was very tight. My opinion is save your maoney and go to a jeweler of plaque company that can do it right, the first time.
warning - disapointed(06-12-2012)
I was not able to get this device to work well even when following the directions. In the end, I was able to load several stamps in a row then tighten up the guide and clamp the assembly to a barrel. Even this way, it was hard to use. The clearance between the plates was too tight to insert the stamps without loosening the side screws. It is hard to get just five stamps into the guide (e.g., 300H&H cannot be done without the alignment risk of a second setup). I wish I had read keydiverfla's review before laying down my money.
Nr produktu: 521104000 LA BOUNTY STEEL STAMP GUIDE Numer części: NONE Precyzyjnie wyrównuje indywidualne stemple stalowe, co pomaga zapewnić, że znaki są proste i równomiernie rozmieszczone podczas stemplowania oznaczeń kalibru na lufach. Śruby z łbem imbusowym pozwalają na regulację odległości między znakami, dzięki czemu osiągasz naprawdę profesjonalne rezultaty. Wyfrezowany otwór zapewnia niezakłócony widok na pierwszą głowicę stempla, co umożliwia prawidłowe ustawienie na elemencie roboczym przed uderzeniem młotkiem. Pasuje do stempli kwadratowych ¼" z rozmiarami znaków 1/16", 3/32" lub 1/8". Pasuje do luf o średnicy do 1-3/8".
319PLN3319,00 zł
*
Czas dostawy ok. 14-21 dni. 3 szt. w magazynie w USA
Dla precyzyjnego wyrównywania podczas znakowania luf
Precyzyjnie wyrównuje indywidualne stemple stalowe, co pomaga zapewnić, że znaki są proste i równomiernie rozmieszczone podczas stemplowania oznaczeń kalibru na lufach. Śruby z łbem imbusowym pozwalają na regulację odległości między znakami, dzięki czemu osiągasz naprawdę profesjonalne rezultaty. Wyfrezowany otwór zapewnia niezakłócony widok na pierwszą głowicę stempla, co umożliwia prawidłowe ustawienie na elemencie roboczym przed uderzeniem młotkiem. Pasuje do stempli kwadratowych ¼" z rozmiarami znaków 1/16", 3/32" lub 1/8". Pasuje do luf o średnicy do 1-3/8".
SPECS: Aluminium, naturalne wykończenie z stalowym U-boltem i okuciami. Długość 2-3⁄8" (6 cm) x szerokość 3¼ (8,2 cm), wysokość 1½ (3,8 cm).
Więcej...
For Precision Alignment When Marking Barrels
Precisely aligns individual steel stamps to help ensure characters are straight and evenly spaced when stamping caliber designations on barrels. Allen head screws allow adjustment for accurate character spacing, so you get truly professional looking results. Machined port allows an unobstructed view of the first stamp head to ensure correct positioning on workpiece prior to tapping with your hammer. Accepts ¼" square stamps with 1/16", 3/32", or 1/8" character sizes. Fits barrels up to 1-3/8" diameter.
SPECS: Aluminum, natural finish with steel U-bolt and hardware. 2-3⁄8" (6cm) long x 3¼ (8.2cm) wide, 1½ (3.8cm) high.
Więcej...
Oceny klientów dla LA BOUNTY STEEL STAMP GUIDE
Liczba ocen: 2
Od brownells.com: 2
Średnia ocena: 1
Caution(08-01-2010)
The device is well made, however it will slip resulting in uneven markings. After reading the instructions over several times I tried it. I was disappointed with the results. I then tried it again on an old barrel and the same thing happened again. I made sure the holding ring was very tight. My opinion is save your maoney and go to a jeweler of plaque company that can do it right, the first time.
warning - disapointed(06-12-2012)
I was not able to get this device to work well even when following the directions. In the end, I was able to load several stamps in a row then tighten up the guide and clamp the assembly to a barrel. Even this way, it was hard to use. The clearance between the plates was too tight to insert the stamps without loosening the side screws. It is hard to get just five stamps into the guide (e.g., 300H&H cannot be done without the alignment risk of a second setup). I wish I had read keydiverfla's review before laying down my money.