Twój koszyk jest pusty.

Koszyk

MURRAYS
SKS ENHANCED FIRING PIN

563000001

Oparte na oryginalnym rosyjskim projekcie dla poprawy funkcjonalności i bezpieczeństwa

Wysokiej jakości, wymienny igliczny oparty na oryginalnym, przedrocznym rosyjskim projekcie, eliminuje ryzyko przypadkowych strzałów samoczynnych i niekontrolowanej pracy w trybie pełnego automatu, które mogą wystąpić w obecnie produkowanych, wolnopływających iglicach. Stopniowy, prosty kształt stożkowy z sprężyną marki Wolff zapobiega mechanicznemu blokowaniu się zamka i gwarantuje konsekwentny powrót iglicy po każdym strzale; dodatkowo, umożliwia użycie amerykańskiej amunicji z miękkimi spłonkami oraz amunicji przeładowanej. Pasuje do chińskich, jugosłowiańskich, albańskich, rumuńskich i rosyjskich karabinów SKS po 1950 roku. Nie jest przeznaczony do użycia w rosyjskich modelach sprzed 1951 roku z płytszym otworem na iglicę. Zestaw zawiera zapasową sprężynę iglicy i instrukcję.

DANE TECHNICZNE: Stal nierdzewna 17-4, wykończenie naturalne. Długość ok. 3¾ cala. Pasuje do rosyjskiego SKS po 1950 roku i klonów.

Więcej...

Based On The Original Russian Design For Improved Function & Safety

High quality, replacement firing pin uses the original, pre-’51 Russian design to eliminate the potential for accidental slam-fires and uncontrollable full-auto operation associated with the current production, free-floating type firing pin. Gradual, straight taper design with Wolff brand spring prevents mechanical lockup in the bolt and ensures consistent firing pin return after every shot; plus, allows the use of soft-primered American ammunition and reloads. Fits Chinese, Yugoslavian, Albanian, Romanian, and post 1950 Russian SKS rifles. Not for use in pre-1951 Russian models with shallower firing pin hole. Includes spare firing pin spring and instructions.

SPECS: 17-4 stainless steel, natural finish. Approx. 3¾” long. Fits post 1950 Russian SKS and clones.

Więcej...

Oceny klientów dla MURRAYS SKS FIRING PIN

Liczba ocen: 23
Od brownells.com: 23
Średnia ocena: 3,6

sks firing pin (26-01-2010)

my sks was unsafe with the old firing pin. the new pin installs very simple works great.will be using this gun more

Murray's is the best (22-08-2010)

I have this item and several other from Murray's. Highly Recommend.

THIS IS A SAFETY ISSUE.

Expensive, but very worth the money. (25-03-2011)

Very well made part - hard, straight, and works as advertised. It's hard to spend [$] on a hundred dollar rifle, but this is worth the money in both safety and reliability. Be sure to check the firing pin hole for a burr that will cause blown primers. Murray's has a page on this on their website - take a look and avoid frustration and damage from blown primers. This mod is needed on any SKS with a floating firing pin. Once you've had a slam-fire or had the gun go full auto and dump the entire magazine, you'll wish you had done this sooner.

Just what the doctor ordered (25-04-2011)

Bought a yugo sks and it would dent the primers but no bang.Very bad situation to be in.Ordered one of these firing pin kits and it worked perfectly.........Very pleased.

Must Have (02-07-2011)

This should be on every SKS, a must have safety feature. thank you Brownells and Ben Murray!

High Quality Part (08-12-2011)

This is a well-engineered replacement firing pin for SKS rifles and will prevent dangerous "slam-fires". The most difficult part in the replacement process is driving the retaining pin out of the bolt. Once the retaining pin is out, the old firing pin will just slide out of the bolt and the new one drops right in. Make sure to push in on the rear of the new firing pin when re-installing the retaining pin in the bolt because the new firing pin is spring loaded. It took me all of 20 minutes to install my new SKS firing pin.

Takes the danger out of SLAM FIRES (05-01-2012)

After haveing a slamfire in my sks I did some searching on the internet. This firing pin is easy to install and works with my Yugo with no problems. With thousand of rounds before and hundreds after the only diffrence is that I KNOW there will NEVER be another slam fire with my gun. Don't wait for a slam fire to happen before you get one of these. get one now and avoid an accident.

A must have (09-02-2012)

this is a very easy fix to a potentially deadly situation. I have only had my SKS about a month and found out about slam fires while doing general research. It only take a few minutes to make this fix and make yourself and others safe.

Agreed, absolute superiority (22-02-2012)

My friends yugo failed to fire multiple times at the range. So, he sold it to me as junk. I havent tested it too mutch yet, but it is a drasticly better design. when you see it you will know it will solve the problem, forever.

Maybe not a permanent solution (18-06-2012)

Worked great for about 600 rounds, then the head of the firing pin broke off inside the rifle.

Great SKS Part (18-08-2012)

This ia a must do fix on all SKS rifles, in my opinion.

Great (10-12-2012)

Super easy instal.
fixed problems of popped primers for me.
Super fast shipping.

No More Slam Fire (13-01-2013)

Made an unsafe sks useable. After repeated cleaning and servicing, rifle would still occasionly slam fire. Installed this enhanced firing pin and solved the problem. I could not be happier

Do Not Recommend (14-01-2013)

I Installed this product in my SKS and Put 200rds (WOLF) thru my SKS to make sure it ran right. i did have a few light primer strikes, so i inspected my rifle and i found that the firing pin broke (Big Chunk Missing from rear of Firing Pin) and my bolt had whats called Volcanoeing which it never had prior to installation. When i removed the firing pin i also noticed that the return spring already lost its spring tension after only 200rds. i highly recommend that you just maintain your rifle properly..................just a tip to Murray's, the hammer does not hit the rear of the firing pin square, it hits at a angle, take a look at a factory SKS firng pin and you'll see what i mean THANKS

Dont buy the hype (09-11-2013)

After 30 or so rounds the spring compressed and pieces broke off jamming the firing pin in the firing pin channel, so it wouldn't fire. Replaced the spring with the one replacement it comes with and the same thing happened after about 30-40 rounds. What a waste of money.

Firing pin (16-12-2013)

At first I loved it until I fired my first 100 rounds through my sks. The spring got bound up into the bolt and it took some time to get it out and replace the spring. After another 200 rounds or so the back end of the pin (where the hammer strikes) broke off and was getting stuck. I took it out shooting about a week later and it stopped firing. So I disassembled the bolt and the firing pin just fell right out and it was in two pieces. I am very displeased with this product. And yes I do thoroughly clean my rifle after every use.

DO NOT BUY WILL HAVE TO REPLACE BOLT (31-05-2014)

i bought this product after no problems with slam-fire but didn't want to experience the problem with my norinco sks after 60 rounds the spring was bound up in the Firing pin channel i replaced the spring with the included one and it will not come out still of the bolt i am going to have to buy a new bolt :( terrible product do not buy unless all you shoot is brass cased american ammo

adds unrealiablity (31-12-2014)

keep it as the russians designed. keep your orgianl clean and it will never fail. i went through hell with this pin. DO NOT BUY

Did not work out for my SKS (15-03-2015)

It's a cool looking firing pin that I bought to use for brass cases. However, it's so cheap to buy and use the steel case stuff. That's where I had the problems. I would estimate about a 10% - 15% ignition failure rate with steel case ammo. I reinstalled the old firing pin and now I have no problems. Would not recommend for steel cased ammo.

JUNK (08-08-2015)

Don't waste money just keep your's clean. Went threw both springs in like 30 rounds and now got to buy the original one again ( doing to old one being bent) and those are getting hard to find.

Murrays SKS Firing Pin! (27-02-2016)

Overpriced piece of junk!

Response to Reviews (02-02-2017)

Murrays response:

Prior to 1-29-2014 some bad batches of 420 SS created brittleness after heat treat, some have broken, but anyone that purchased prior to that date qualifies for free replacement. Contact Murrays for details. Since that date, we have shipped over 5K of the new 17-4 SS FPs and not one has been reported broken. "Popped Primers" can affect our FP the same as an "original" FP, but we have the new "Neck & Throat" service that is a 100% cure for that as well. Again, contact Murrays for details. Brownells has our phone number and email address.

This is a winner -- when needed (20-07-2017)

My Chinese SKS would double on me almost every magazine making for unsafe use. This occurred even though the bolt, firing pin, and firing pin channel were clean and even though the firing pin moved freely in the bolt when shaken, as itâs supposed to. I replaced the stock firing pin in my Chinese SKS with the Murray firing pin and spring and fired 100 rounds without a single hiccup, for the first time. Highly recommended when your SKS just wonât behave.

Zobacz 23 dodatkowych opinii na brownells.com

379 379 1 PLN

Nr produktu: 563000001
MURRAYS SKS FIRING PIN
Numer części: SKSFIRINGPIN Wysokiej jakości, wymienny igliczny oparty na oryginalnym, przedrocznym rosyjskim projekcie, eliminuje ryzyko przypadkowych strzałów samoczynnych i niekontrolowanej pracy w trybie pełnego automatu, które mogą wystąpić w obecnie produkowanych, wolnopływających iglicach. Stopniowy, prosty kształt stożkowy z sprężyną marki Wolff zapobiega mechanicznemu blokowaniu się zamka i gwarantuje konsekwentny powrót iglicy po każdym strzale; dodatkowo, umożliwia użycie amerykańskiej amunicji z miękkimi spłonkami oraz amunicji przeładowanej. Pasuje do chińskich, jugosłowiańskich, albańskich, rumuńskich i rosyjskich karabinów SKS po 1950 roku. Nie jest przeznaczony do użycia w rosyjskich modelach sprzed 1951 roku z płytszym otworem na iglicę. Zestaw zawiera zapasową sprężynę iglicy i instrukcję.

379 PLN 4 379,00 zł *

Czas dostawy ok. 14-21 dni.
4 szt. w magazynie w USA

Specyfikacja: Make: SKS

Dodaj do listy zakupów

Zapytaj

Szczegóły

Dodaj do listy zakupów

Zapytaj

Cechy

Wytwórca: SKS Waga dostawy: 0,014kg Szerokość wysyłki: 83mm Długość wysyłki: 146mm

Szczegóły pozycji

Made in USA
US export classification: 0A501.x

Oparte na oryginalnym rosyjskim projekcie dla poprawy funkcjonalności i bezpieczeństwa

DANE TECHNICZNE: Stal nierdzewna 17-4, wykończenie naturalne. Długość ok. 3¾ cala. Pasuje do rosyjskiego SKS po 1950 roku i klonów.

Więcej...

Based On The Original Russian Design For Improved Function & Safety

SPECS: 17-4 stainless steel, natural finish. Approx. 3¾” long. Fits post 1950 Russian SKS and clones.

Więcej...

Oceny klientów dla MURRAYS SKS FIRING PIN

Liczba ocen: 23
Od brownells.com: 23
Średnia ocena: 3,6

sks firing pin (26-01-2010)

my sks was unsafe with the old firing pin. the new pin installs very simple works great.will be using this gun more

Murray's is the best (22-08-2010)

I have this item and several other from Murray's. Highly Recommend.

THIS IS A SAFETY ISSUE.

Expensive, but very worth the money. (25-03-2011)

Just what the doctor ordered (25-04-2011)

Bought a yugo sks and it would dent the primers but no bang.Very bad situation to be in.Ordered one of these firing pin kits and it worked perfectly.........Very pleased.

Must Have (02-07-2011)

This should be on every SKS, a must have safety feature. thank you Brownells and Ben Murray!

High Quality Part (08-12-2011)

Takes the danger out of SLAM FIRES (05-01-2012)

A must have (09-02-2012)

Agreed, absolute superiority (22-02-2012)

Maybe not a permanent solution (18-06-2012)

Worked great for about 600 rounds, then the head of the firing pin broke off inside the rifle.

Great SKS Part (18-08-2012)

This ia a must do fix on all SKS rifles, in my opinion.

Great (10-12-2012)

Super easy instal.
fixed problems of popped primers for me.
Super fast shipping.

No More Slam Fire (13-01-2013)

Made an unsafe sks useable. After repeated cleaning and servicing, rifle would still occasionly slam fire. Installed this enhanced firing pin and solved the problem. I could not be happier

Do Not Recommend (14-01-2013)

Dont buy the hype (09-11-2013)

Firing pin (16-12-2013)

DO NOT BUY WILL HAVE TO REPLACE BOLT (31-05-2014)

adds unrealiablity (31-12-2014)

keep it as the russians designed. keep your orgianl clean and it will never fail. i went through hell with this pin. DO NOT BUY

Did not work out for my SKS (15-03-2015)

JUNK (08-08-2015)

Don't waste money just keep your's clean. Went threw both springs in like 30 rounds and now got to buy the original one again ( doing to old one being bent) and those are getting hard to find.

Murrays SKS Firing Pin! (27-02-2016)

Overpriced piece of junk!

Response to Reviews (02-02-2017)

This is a winner -- when needed (20-07-2017)

Zobacz 23 dodatkowych opinii na brownells.com

Sugerowane pozycje
Klienci kupili także

DAVID TUBB REMINGTON 700 LONG ACTION
MODEL 700 SPEEDLOCK FIRING PIN KITS

DAVID TUBB

Niedostępne

Iglice

3,3

WMD GUNS NIB-X® CHARGING HANDLE
AR-15/M16 NiB-X® CHARGING HANDLE

WMD GUNS

W magazynie

274,00 zł *

Rączki zamkowe

AERO PRECISION 15" AR-15 ATLAS R-ONE M-LOK HANDGUARDS, BLACK
AR-15 ATLAS R-ONE HANDGUARDS M-LOK

AERO PRECISION

W magazynie

1 319,00 zł * 1 059,00 zł - 1 389,00 zł*

Szyny i łoża

BERETTA USA BERETTA CX4 FRONT SIGHT END CAP BLACK
BERETTA CX4 FRONT SIGHT END CAP BLACK

BERETTA USA

W magazynie

304,00 zł *

Nakładki muszki

TANDEMKROSS TITAN EXTENDED MAG RELEASE FOR RUGER® PC CARBINE® RED
"TITAN" EXTENDED MAGAZINE RELEASE FOR RUGER™ PC CARBINE

TANDEMKROSS

W magazynie

269,00 zł * 234,00 zł - 269,00 zł*

Zatrzaski magazynków

MAGPUL MOE M-LOK HANDGUARD, RILFE, BLACK
AR-15/M16 MOE M-LOK RIFLE HANDGUARDS

MAGPUL

W magazynie

269,00 zł *

Szyny i łoża

Zaloguj się

Nie pamiętasz hasła?
Zarejestruj się

Kontakt

Facebook

Mapa strony

Kategorie produktów

Zamawianie

Obsługa klienta

Witamy!

Witamy w brownells.pl wiodącym dostawcy w Polsce akcesoriów do broni, części broni, narzędzi rusznikarskich, narzędzi do elaboracji amunicji oraz komponentów.

Co oferujemy

Lubisz strzelać, pracujesz przy naprawach broni zawodowo lub hobbystycznie lub po prostu jesteś właścicielem broni, to nasza strona jest właśnie dla Ciebie!

Przez ponad 75 lat strzelcy, rusznikarze, hobbyści, wojskowi, służby specjalne korzystają z usług Brownells jako dostawcy szerokiego asortymentu, wysokiej jakości części broni. Znajdziesz ponad 90 000 produktów w tym części nietypowe, akcesoria, narzędzia rusznikarskie i inne produkty do utrzymania, naprawy i ulepszania swojej broni.