Fluorescentny zielony, bojowy popychacz magazynka z występem na głowie, który natychmiast pokazuje wzrokowo lub dotykiem, czy magazynek jest pusty. Wykonany z niekorodującego, wytrzymałego tworzywa ABS o wysokim wpływie, z zwężającym się ogonem, aby zapobiec blokowaniu się sprężyny magazynka i zwiększyć niezawodność.
DANE TECHNICZNE: Długość 1.7" (4.5cm), średnica .91" (23mm). Tylko kaliber 12. Pasuje do Remington 870, 1100 oraz innych różnych strzelb z magazynkiem bez zatrzasków.
Więcej...
Fluorescent green, combat-style follower with projection on the head, instantly shows by sight, or by touch, if mag is empty. Molded from non-rusting, high-impact grade ABS with tapered tail to help prevent magazine spring bind and improve reliability.
SPECS: 1.7" (4.5cm) long, .91" (23mm) diameter. 12 ga. only. Fits Remington 870, 1100 and other miscellaneous shotguns with no detents in magazine tube.
Liczba ocen: 8
Od brownells.com: 8
Średnia ocena: 3,6
= one less(15-01-2011)
Terrible design! Limits the tube capacity by one round, deforms slightly in the tube and then binds as it moves towards the receiver.
Edgard Villa(20-03-2011)
Will fit some newer Remington 870 only with some minor "Dremel" fitting.
Works great!(16-05-2011)
This works great in my 870. I removed the dimples as I added a mag. tube extension. I have had no issues in several hundred rounds. It is solid and made of a tough plastic, not some brittle cheap feeling material. I am sure it will wear very well. The extended "tail" keeps it aligned properly in the spring. It doesn't limit my capacity of 2 3/4" shells.
Magazine Follower Doesn't Follow(28-10-2011)
This binded in the tube after running a single test round through it. Had to knock it free with a screwdriver. Complete waste of the money; glad there's nothing wrong with my original follower.
Good item(15-01-2012)
Use in my 870, Buying another for my 1100. Hi-vis to see magazine is empty at a glance, and acts as a spring guide when spring is fully compressed. There is a reason why expensive mod. kits/shotguns come with this follower.
pro and con(21-04-2015)
all is good with this follower except for the loss of one round in my extended magazine ( went from 7 plus one to 6 plus one), but i think if i cut and file off about half inch from the tail section of the follower, should get back my seventh round. great color and feel on empty mag.
Magazine tube extension(09-06-2016)
I installed a 5 rd mag extension on my 870 and replaced the factory follower with this. One problem. the back edge was "too sharp" to pass where the detents had been. So, I took my Dremel and ground down the edge at an angle about an eighth of an inch. Works perfectly now!
Love it(21-07-2017)
Nicely priced, the product itself is solid. I have an 870 express mag with dimples still on the tube (4shot), 5 minutes with a rounded file and the follower fell in without issue. Still have plenty of room in the tube and retain 4 shells in the mag.
Nr produktu: 800100004 SCATTERGUN TECHNOLOGY REMINGTON 870 MAGAZINE FOLLOWER, 12 GA. Numer części: SGHVF683507710193 Fluorescentny zielony, bojowy popychacz magazynka z występem na głowie, który natychmiast pokazuje wzrokowo lub dotykiem, czy magazynek jest pusty. Wykonany z niekorodującego, wytrzymałego tworzywa ABS o wysokim wpływie, z zwężającym się ogonem, aby zapobiec blokowaniu się sprężyny magazynka i zwiększyć niezawodność.
79PLN079,00 zł
*
Zaległe, czas dostawy ok. 4-12 tygodni z magazynu w USA.
Fluorescentny zielony, bojowy popychacz magazynka z występem na głowie, który natychmiast pokazuje wzrokowo lub dotykiem, czy magazynek jest pusty. Wykonany z niekorodującego, wytrzymałego tworzywa ABS o wysokim wpływie, z zwężającym się ogonem, aby zapobiec blokowaniu się sprężyny magazynka i zwiększyć niezawodność.
DANE TECHNICZNE: Długość 1.7" (4.5cm), średnica .91" (23mm). Tylko kaliber 12. Pasuje do Remington 870, 1100 oraz innych różnych strzelb z magazynkiem bez zatrzasków.
Więcej...
Fluorescent green, combat-style follower with projection on the head, instantly shows by sight, or by touch, if mag is empty. Molded from non-rusting, high-impact grade ABS with tapered tail to help prevent magazine spring bind and improve reliability.
SPECS: 1.7" (4.5cm) long, .91" (23mm) diameter. 12 ga. only. Fits Remington 870, 1100 and other miscellaneous shotguns with no detents in magazine tube.
Liczba ocen: 8
Od brownells.com: 8
Średnia ocena: 3,6
= one less(15-01-2011)
Terrible design! Limits the tube capacity by one round, deforms slightly in the tube and then binds as it moves towards the receiver.
Edgard Villa(20-03-2011)
Will fit some newer Remington 870 only with some minor "Dremel" fitting.
Works great!(16-05-2011)
This works great in my 870. I removed the dimples as I added a mag. tube extension. I have had no issues in several hundred rounds. It is solid and made of a tough plastic, not some brittle cheap feeling material. I am sure it will wear very well. The extended "tail" keeps it aligned properly in the spring. It doesn't limit my capacity of 2 3/4" shells.
Magazine Follower Doesn't Follow(28-10-2011)
This binded in the tube after running a single test round through it. Had to knock it free with a screwdriver. Complete waste of the money; glad there's nothing wrong with my original follower.
Good item(15-01-2012)
Use in my 870, Buying another for my 1100. Hi-vis to see magazine is empty at a glance, and acts as a spring guide when spring is fully compressed. There is a reason why expensive mod. kits/shotguns come with this follower.
pro and con(21-04-2015)
all is good with this follower except for the loss of one round in my extended magazine ( went from 7 plus one to 6 plus one), but i think if i cut and file off about half inch from the tail section of the follower, should get back my seventh round. great color and feel on empty mag.
Magazine tube extension(09-06-2016)
I installed a 5 rd mag extension on my 870 and replaced the factory follower with this. One problem. the back edge was "too sharp" to pass where the detents had been. So, I took my Dremel and ground down the edge at an angle about an eighth of an inch. Works perfectly now!
Love it(21-07-2017)
Nicely priced, the product itself is solid. I have an 870 express mag with dimples still on the tube (4shot), 5 minutes with a rounded file and the follower fell in without issue. Still have plenty of room in the tube and retain 4 shells in the mag.