Stały nacisk sprężyny utrzymuje rampy/bazy przednie lub tylne na miejscu - idealnie także na celowniki .45; Wszechstronny, w pełni regulowany design; Doskonała przestrzeń dla palnika
Rozwiązuje problem "przesunięcia się rampy w momencie topnienia lutowia" dzięki zastosowaniu spiczastego, sprężynującego tłoka, który utrzymuje stały nacisk na rampę lub celownik .45, nawet gdy lut się rozpływa. Możliwość regulacji wysokości, kąta i siły nacisku sprężyny. Niezadzierająca podstawa "V" centruje lufę pod tłokiem. Utrzymuje również w miejscu bazy przyrządów celowniczych. Zapewnia dużą przestrzeń dla palnika.
SPECYFIKACJE: Długość bazy aluminiowej 2" (5,1 cm). Wysokość całkowita 4" (10,2 cm). Długość ramienia 1-3/8" (3,5 cm). Długość podpory tłoka 2" (5,1 cm), długość montażu tłoka 3" (7,6 cm).
Więcej...
Spring Pressure Keeps Front Or Rear Ramps/Bases In Place- Perfect On .45 Sights Too; Versatile, Totally Adjustable Design; Excellent Torch Clearance
Cures the "ramp slips just as the solder melts" problem with a pointed, spring-loaded plunger that keeps constant pressure on the ramp or a .45 sight, even when the solder flows. Adjusts for height, angle and amount of spring pressure. Non-marring, "V" block base centers barrel under the plunger. Holds rear sight bases in place, too. Great torch clearance.
SPECS: 2" (5.1cm) long aluminum Base. 4" (10.2cm) high overall. 1-3/8" (3.5cm) long over-arm. 2" (5.1cm) long Plunger Support, 3" (7.6cm) long Plunger Assembly.
Więcej...
Oceny klientów dla BROWNELLS RAMP SOLDERING JIG
Liczba ocen: 2
Od brownells.com: 2
Średnia ocena: 3,5
Love this Jig(21-05-2011)
Used this jig to silver solder Moison nagant front sights back on. Got it on perfect.
Defective(31-07-2015)
I purchased one of these jigs several years ago but did not try it out until recently. The spring-loaded plunger was not perpendicular to the base, so it sat at a slight angle of 5-10 degrees. This prevented full downward pressure onto the workpiece and tended to cause slippage. The plunger has a pointed tip which provides for a less secure hold than a flat tip. I suppose a small flat could be ground on it. To prevent sight rotation during soldering, the base needs to be sitting on a flat surface. Since temperatures are around 1000 degrees, a metal table is the only suitable work surface. The barrel needs to be level and secure as well, so a padded vise is advisable. This requires aligning the vise and metal table so the sight and barrel are level with the jig. It's a clever design, so I am returning the jig for replacement. Hopefully the next one will be more square.
Nr produktu: 080739000 BROWNELLS RAMP SOLDERING JIG050806104372 Rozwiązuje problem "przesunięcia się rampy w momencie topnienia lutowia" dzięki zastosowaniu spiczastego, sprężynującego tłoka, który utrzymuje stały nacisk na rampę lub celownik .45, nawet gdy lut się rozpływa. Możliwość regulacji wysokości, kąta i siły nacisku sprężyny. Niezadzierająca podstawa "V" centruje lufę pod tłokiem. Utrzymuje również w miejscu bazy przyrządów celowniczych. Zapewnia dużą przestrzeń dla palnika.
589PLN0589,00 zł
*
Zaległe, czas dostawy ok. 4-12 tygodni z magazynu w USA.
Stały nacisk sprężyny utrzymuje rampy/bazy przednie lub tylne na miejscu - idealnie także na celowniki .45; Wszechstronny, w pełni regulowany design; Doskonała przestrzeń dla palnika
Rozwiązuje problem "przesunięcia się rampy w momencie topnienia lutowia" dzięki zastosowaniu spiczastego, sprężynującego tłoka, który utrzymuje stały nacisk na rampę lub celownik .45, nawet gdy lut się rozpływa. Możliwość regulacji wysokości, kąta i siły nacisku sprężyny. Niezadzierająca podstawa "V" centruje lufę pod tłokiem. Utrzymuje również w miejscu bazy przyrządów celowniczych. Zapewnia dużą przestrzeń dla palnika.
SPECYFIKACJE: Długość bazy aluminiowej 2" (5,1 cm). Wysokość całkowita 4" (10,2 cm). Długość ramienia 1-3/8" (3,5 cm). Długość podpory tłoka 2" (5,1 cm), długość montażu tłoka 3" (7,6 cm).
Więcej...
Spring Pressure Keeps Front Or Rear Ramps/Bases In Place- Perfect On .45 Sights Too; Versatile, Totally Adjustable Design; Excellent Torch Clearance
Cures the "ramp slips just as the solder melts" problem with a pointed, spring-loaded plunger that keeps constant pressure on the ramp or a .45 sight, even when the solder flows. Adjusts for height, angle and amount of spring pressure. Non-marring, "V" block base centers barrel under the plunger. Holds rear sight bases in place, too. Great torch clearance.
SPECS: 2" (5.1cm) long aluminum Base. 4" (10.2cm) high overall. 1-3/8" (3.5cm) long over-arm. 2" (5.1cm) long Plunger Support, 3" (7.6cm) long Plunger Assembly.
Więcej...
Oceny klientów dla BROWNELLS RAMP SOLDERING JIG
Liczba ocen: 2
Od brownells.com: 2
Średnia ocena: 3,5
Love this Jig(21-05-2011)
Used this jig to silver solder Moison nagant front sights back on. Got it on perfect.
Defective(31-07-2015)
I purchased one of these jigs several years ago but did not try it out until recently. The spring-loaded plunger was not perpendicular to the base, so it sat at a slight angle of 5-10 degrees. This prevented full downward pressure onto the workpiece and tended to cause slippage. The plunger has a pointed tip which provides for a less secure hold than a flat tip. I suppose a small flat could be ground on it. To prevent sight rotation during soldering, the base needs to be sitting on a flat surface. Since temperatures are around 1000 degrees, a metal table is the only suitable work surface. The barrel needs to be level and secure as well, so a padded vise is advisable. This requires aligning the vise and metal table so the sight and barrel are level with the jig. It's a clever design, so I am returning the jig for replacement. Hopefully the next one will be more square.