876430008790 Jednoczęściowa konstrukcja łączy pierścień i podstawę w jedną jednostkę. Eliminacja połączenia pierścienia/podstawy nie tylko minimalizuje wagę, ale także zapewnia mocniejszy montaż. Każda pokrywa pierścienia ma szerokość 5⁄8", z czterema śrubami TORX, aby zapobiec przesuwaniu się lub przesunięciu dużych lunet. Zaprojektowane przez Mela Forbesa z New Ultralight Arms.
W magazynie
Czas dostawy ok. 14-21 dni. 4 szt. w magazynie w USA
Czas dostawy ok. 14-21 dni. 4 szt. w magazynie w USA
Gdy każdy gram ma znaczenie; Siła stali bez dodatkowego ciężaru
Jednoczęściowa konstrukcja łączy pierścień i podstawę w jedną jednostkę. Eliminacja połączenia pierścienia/podstawy nie tylko minimalizuje wagę, ale także zapewnia mocniejszy montaż. Każda pokrywa pierścienia ma szerokość 5⁄8", z czterema śrubami TORX, aby zapobiec przesuwaniu się lub przesunięciu dużych lunet. Zaprojektowane przez Mela Forbesa z New Ultralight Arms.
SPECS: Aluminium serii 7000, czarny, anodowany, matowe wykończenie. Akceptuje lunety o średnicy 1", chyba że w kolumnie dopasowania podano inaczej dla lunet o średnicy 30mm. Wysokość od dolnej części pierścienia do górnej części receivera: Niska - .400" (10.1mm), Średnia - .500" (12.7mm). Wysoka - .640" (16.3mm), X‑Wysoka - .740" (18.8mm). Przybliżona waga 2.1 oz. (59 g). Niektóre wysokości mogą się różnić, zobacz tabelę poniżej. Rem. 700 pasuje również do modeli 721/722/725 i 40X. Rem. Model Seven pasuje do receiverów z czterema otworami na śruby. Savage AccuTrigger pasuje do receiverów centerfire z okrągłym górnym pokryciem i AccuTrigger. Win. 70 pasuje tylko do rozstawu tylnych otworów .860".
When Every Ounce Counts; The Strength Of Steel Without The Weight
One-piece construction blends the ring and base into a single unit. Eliminating the ring/base joint not only keeps weight to a minimum, it provides a stronger mount. Each ring cap is 5⁄8" wide, with four, TORX screws, to keep large scopes from slipping or shifting. Designed by Mel Forbes of New Ultralight Arms.
SPECS: 7000 series aluminum, black, anodized, matte finish. Accepts 1" dia. scopes, unless otherwise listed in fits column for 30mm dia. scopes. Height from bottom of ring to top of receiver: Low - .400" (10.1mm), Med - .500" (12.7mm). High - .640" (16.3mm), X‑High - .740" (18.8mm). Approx. weight 2.1 oz. (59 g). Some heights vary, see chart below. Rem. 700 also fits 721/722/725 and 40X models. Rem. Model Seven fits receivers with four screw holes. Savage AccuTrigger fits round top centerfire receivers with AccuTrigger. Win. 70 fits .860" rear hole spacing only.
Top takeaways
Jednoczęściowa konstrukcja
Minimalna waga
Wysoka wytrzymałość
Cechy
Elevation:0 MOA
Model:Vanguard,1500
Rodzaj wykończenia:Black
Styl:Direct Mount
Typ broni:Howa,Weatherby
Wysokość:.500''
Średnica tubusa:30mm
Waga dostawy:0,111kg
Wysokość wysyłki:64mm
Szerokość wysyłki:98mm
Długość wysyłki:229mm
UPC:876430008790
Szczegóły pozycji
Made in USA
Opinie klientów
Oceny klientów (13)
4,8 / 5
Zdecydowanie polecane
The BEST I've found for 10/22's. 01-05-2014
I've installed these rings on 5 or 6 guns now. These are the nicest looking and best working scope mounts I have found for 10/22's if you want a nice traditional look and you're sick of seeing miles of picatinny rail on every gun you own. They are offset so you can reverse each one to get good positioning on the scope tube (as close to the occular and objective lenses as possible while staying away from the erector tube area), they are very well finished, easy to install, line up perfectly and are very sturdy. Order the MEDIUM height for any scope with an objective between 51 and 57 mm. Order LOW height for scopes 50 mm and under. Good shootin'!!
Zdecydowanie polecane
Perfect 23-01-2014
Mounting a Leupold 6.5-20x40 on a Savage 12 BJTV w/ thumbhole stock and needed the scope as low as possible. These low extended rings were THE PERFECT solution. Scope is now EXACTLY where I wanted it.
I have 4 sets of Talley rings on 4 separate rifles and could not ask for better rings. Best rings for the dollar out there.
Zdecydowanie polecane
Delightfully clean 10/22 scope mounts 10-08-2013
These scope mounts for the Ruger 10/22 are absolutely elegant. Let me share some background info that can help make this relevant to everyone who appreciates 10/22s.
I love 10/22s -- at the moment I have five. I tweak and tune the daylights out of them for both performance and appearance. I'm fond of the contour of the 10/22 receiver and feel Ruger's furnished mount base spoils the lines. For this reason I've made small one-piece bases for my halographic red dots and small two-piece bases for scopes and tube-type red dots -- all starting from Ruger's base.
With the Talley bases, this is no longer necessary. They cover a minimum of the top of the receiver. They're beautifully made and finished. And they hold a scope tightly without marring the finish.
My only wish is that they were also available in a silver finish. They'd look spectacular with my silver Ultradot red dots on my stainless10/22s. I might buy additional black ones and send them off to be reanodized silver. I like them that much.
Zdecydowanie polecane
GREAT RINGS 10-01-2013
THEY ARE TRUE, LITE, AND HAVE TORX SCREWS SO THEY CAN BE REMOVED AND TIGHTENED MANY TIMES IF NEEDED. 25#S OF TORQUE IS PLENTY. GREAT PRODUCT.
Zdecydowanie polecane
Excellent Product 09-07-2012
These are the best rings I have found for my custom Mauser rifles. The finish is good enough I do not need to polish and re-finish to make them match the Matte finish of Leupold scopes. They are better than some of the more costly rings I have bought and have built in bases so one less thing to buy.
Zdecydowanie polecane
excellant 28-10-2011
I used these to install a Bushnell Elite scope on my Browning A bolt. The rings fit perfectly and are very secure.
Zdecydowanie polecane
Great Rings! 23-08-2011
Used this to mount a varmint scope (42mm objective) on my Anschutz 1732 in .22 Hornet. Height was perfect for this application, leaving only a few millimeters of space between the barrel and scope. A bigger objective scope would require higher rings. Easy to install, well made, and rock solid mount and ring combination.
Zdecydowanie polecane
A-Bolt LW Scope Mount 20-11-2010
I used these to mount a 2.5 X 8 Leupold on a 20" Micro Hunter. They're extremely light, but appear to be rugged. The fit is perfect, the scope lined up very square, no need for lapping. I torqued the base screws @ 30 inch/lbs and a touch of blue loctite. The ring screws were evenly torqued @ 22.5. They compliment the clean lines of the little carbine without sacrificing quality. It placed the scopes objective about 1/4" above the barrel, and allowed more than an ample amount of placement for eye relief. I'm sold.
Polecane z zastrzeżeniami
Great quality, not very 28-09-2010
Wanted to replace the medium-height rings that came with my Tikka T3 in 6.5x55 with some that were stronger and lower. I prefer to use a 2-7x32 scope and like to mount it nice and low. The Talley "low" rings, while very strong and well-made, appear to have enough room for a 40mm objective lens scope. They don't appear to be any lower than the factory rings. Other than that (and some embarrassing typos on the packaging), they are great.
Zdecydowanie polecane
Perfect fit for short action 07-03-2010
I mounted these on a Winchester Ranger short action and the fit is perfect. I tried a few other brands, two-piece bases overlapped the action area and one-piece bases did not fit (the ranger action is a bit shorter than a standard short action). They look great on the gun and alignment was right on. No shims required.
Zdecydowanie polecane
Long-term Test 16-01-2010
I put a set of these on my Tikka in .338 Winchester magnum several years ago after the "B" brand failed to hold the scope. My hunting load sends a 225 gr bullet out the muzzle at 2900 fps over my Oehler chrono; there is recoil. The Talley lightweights hold the Zeiss 3.5-10X scope absolutely rock solid year after year of hard hunting use in Montana. This is a quality product.
Zdecydowanie polecane
THE BEST - BAR NONE 07-12-2009
I have sixteen scoped guns and have experience with a number of name brand manufacturers of bases and rings. Tally makes a product that is simple to install and, at least in my case, needed no shimming or adjustments to align the rings which I check with a Sinclair Scope Alignment Tool. So far I have mounted three scopes with Tally mounts with no problem. Nuff said.
Zdecydowanie polecane
Great Product 07-10-2009
I was sort of skeptical about how these would work (no allowance for adjustments), but I heard a good report about Talley, so I gave them a shot. Great fit and finish, and no adjustment needed. In fact, the positional tolerances on these things are so good, that my scope needed less adjustment than with any other type of mounting system I've used lately. Note: For the medium height setup, a 40mm scope is the max. diameter for the Marlin 336.
Odpowiedzialny podmiot gospodarczy zgodnie z rozporządzeniem UE
Brownells Polska Sp. z o.o.
Armii Krajowej 77
05-071 Sulejówek
Polska
info@brownells.pl
Instrukcja Bezpieczeństwa dla Montażu Lunety LIGHT WEIGHT SCOPE MOUNT TALLEY HOWA 1500 MEDIUM 30MM
Wprowadzenie
Dziękujemy za zakup montażu lunety LIGHT WEIGHT SCOPE MOUNT TALLEY HOWA 1500 MEDIUM 30MM. Niniejsza instrukcja bezpieczeństwa ma na celu zapewnienie bezpiecznego użytkowania produktu oraz dostarczenie ważnych informacji dotyczących instalacji, użytkowania i utylizacji. Prosimy o dokładne zapoznanie się z poniższymi wytycznymi.
Ogólne zasady bezpieczeństwa
Upewnij się, że montaż jest odpowiedni do posiadanej lunety oraz broni.
Zawsze sprawdzaj, czy wszystkie elementy montażu są w dobrym stanie przed użyciem.
Nie używaj montażu, jeśli zauważysz jakiekolwiek uszkodzenia lub wady.
Przechowuj montaż w suchym miejscu, aby zapobiec korozji lub uszkodzeniom mechanicznym.
Nie pozwól dzieciom na zabawę z montażem ani jego elementami.
Specyficzne środki ostrożności podczas użytkowania
Zawsze stosuj się do instrukcji producenta dotyczących montażu lunety.
Używaj odpowiednich narzędzi, aby uniknąć uszkodzenia śrub i elementów montażu.
Unikaj nadmiernego dokręcania śrub, co może prowadzić do uszkodzenia montażu lub lunety.
Regularnie sprawdzaj, czy montaż jest stabilny i nie wymaga regulacji.
Zwracaj uwagę na otoczenie podczas korzystania z broni, aby zapewnić bezpieczeństwo sobie i innym.
Instrukcje dotyczące instalacji i użytkowania
Przygotowanie do montażu:
Upewnij się, że wszystkie części montażu są dostępne i w dobrym stanie.
Zidentyfikuj odpowiednie miejsce na broni do zamontowania lunety.
Montaż lunety:
Umieść lunetę w pierścieniach montażowych.
Użyj śrub TORX do zabezpieczenia lunety w montażu.
Dokręć śruby równomiernie, aby zapewnić stabilność lunety.
Sprawdzenie stabilności:
Po zakończeniu montażu, sprawdź, czy luneta jest stabilna i nie porusza się.
Wykonaj testy na strzelnicy, aby upewnić się, że montaż działa prawidłowo.
Użytkowanie:
Używaj lunety zgodnie z jej przeznaczeniem.
Regularnie kontroluj stan montażu i lunety, aby upewnić się, że działają prawidłowo.
Instrukcje dotyczące utylizacji
Utylizuj produkt zgodnie z lokalnymi przepisami dotyczącymi odpadów.
Nie wyrzucaj produktu do zwykłego kosza na śmieci.
Skontaktuj się z lokalnymi władzami w celu uzyskania informacji o odpowiednich metodach utylizacji.
Informacje kontaktowe w celu uzyskania dalszego wsparcia
W przypadku pytań lub wątpliwości dotyczących montażu lunety, skontaktuj się z odpowiednim punktem obsługi klienta.
Podsumowanie
Zastosowanie się do powyższych instrukcji pomoże zapewnić bezpieczne użytkowanie montażu lunety LIGHT WEIGHT SCOPE MOUNT TALLEY HOWA 1500 MEDIUM 30MM. Pamiętaj, że odpowiedzialne korzystanie z broni i akcesoriów jest kluczowe dla bezpieczeństwa użytkownika oraz otoczenia.
Napotkaliśmy błąd podczas wczytywania tej zawartości. Odśwież stronę, aby kontynuować. Jeśli problem będzie się powtarzał, skontaktuj się z naszym działem obsługi klienta.