Te stalowe pierścienie blokujące matryce od Hornady obejmują cały obwód korpusu matrycy. Śruba blokująca ściska pierścień wokół matrycy, zapewniając stały nacisk na gwinty - bez śrub zaciskowych. Pierścienie mają płaską powierzchnię z każdej strony do użytku z kluczem. Pierścienie Sure-Lock pasują do wszystkich standardowych matryc do ładowania o gwincie 7/8""-14.
Więcej...
These steel die lock rings from Hornady clamp around the entire circumference of the die body. The lock screw squeezes the lock ring around the die with constant pressure across the threads - no jam screws. These rings have a flat on each side for wrench use. Sure-Lock Rings fit all standard 7/8""-14 reloading dies.
Więcej...
Oceny klientów dla HORNADY LOCK RINGS
Liczba ocen: 5
Od brownells.com: 5
Średnia ocena: 4,2
excelent(28-07-2011)
this is an excelent replacement rign for any die set. you dont have to worry about stripping out the brass set screw like on other models and it squeezes the ring on the die instead of the screw contacting the threads of the die. because it isnt touching the threads so the set screw is made of steel and it will last you forever.
Great Ring(04-05-2012)
A good ring because you can lock it and also crank it down with wrench rather than having to mess with a channel-lock.
Works with Co-Ax press?(15-03-2013)
As stated in many places "works with Forster Co-ax press" NOT! Might be to a design change, but very sloppy fit in this press. Constant misalignment on smaller cases. Case mouth hits decapping pin assembly 90% of the time. Bought 10 of these with the press, my mistake.
All die makers should use this design(10-08-2014)
I have Hornady, RCBS, Forster, Redding and Lee dies on my bench. I have found over time that I prefer the Hornady locking ring design. The ring is easily tightened with the included hex key. This design tensions the entire bearing surface of the ring, rather than a single point-of-contact set-screw.
When I buy a new non-Hornady die, the first thing I do is replace the locking ring with one of these.
Hornady Die lock rings(25-07-2017)
Nothing bothers me more than poorly designed die lock rings. My past history of 45 years of reloading began with the old RCBS lead pellet/setscrew system that impinged on the 7/8-14 threads of the die making it very difficult to adjust or remove off the die. Advancements then used brass setscrews then angled split ring design at a tangent to the threads which adjusted themselves closed against the threads,a much improved version.These Hornady lock rings allow their propriatory red handled wrench to properly secure this split ring tightly against the press body. Other manufacturers use their wrenches but still use the old setscrew that crushes against the die threads. I recommend these lock rings over any other type to include "O" ring spongy attachments.
Nr produktu: 749000313 HORNADY LOCK RINGS Numer części: 044000090255440003 Te stalowe pierścienie blokujące matryce od Hornady obejmują cały obwód korpusu matrycy. Śruba blokująca ściska pierścień wokół matrycy, zapewniając stały nacisk na gwinty - bez śrub zaciskowych. Pierścienie mają płaską powierzchnię z każdej strony do użytku z kluczem. Pierścienie Sure-Lock pasują do wszystkich standardowych matryc do ładowania o gwincie 7/8""-14.
Te stalowe pierścienie blokujące matryce od Hornady obejmują cały obwód korpusu matrycy. Śruba blokująca ściska pierścień wokół matrycy, zapewniając stały nacisk na gwinty - bez śrub zaciskowych. Pierścienie mają płaską powierzchnię z każdej strony do użytku z kluczem. Pierścienie Sure-Lock pasują do wszystkich standardowych matryc do ładowania o gwincie 7/8""-14.
Więcej...
These steel die lock rings from Hornady clamp around the entire circumference of the die body. The lock screw squeezes the lock ring around the die with constant pressure across the threads - no jam screws. These rings have a flat on each side for wrench use. Sure-Lock Rings fit all standard 7/8""-14 reloading dies.
Więcej...
Oceny klientów dla HORNADY LOCK RINGS
Liczba ocen: 5
Od brownells.com: 5
Średnia ocena: 4,2
excelent(28-07-2011)
this is an excelent replacement rign for any die set. you dont have to worry about stripping out the brass set screw like on other models and it squeezes the ring on the die instead of the screw contacting the threads of the die. because it isnt touching the threads so the set screw is made of steel and it will last you forever.
Great Ring(04-05-2012)
A good ring because you can lock it and also crank it down with wrench rather than having to mess with a channel-lock.
Works with Co-Ax press?(15-03-2013)
As stated in many places "works with Forster Co-ax press" NOT! Might be to a design change, but very sloppy fit in this press. Constant misalignment on smaller cases. Case mouth hits decapping pin assembly 90% of the time. Bought 10 of these with the press, my mistake.
All die makers should use this design(10-08-2014)
I have Hornady, RCBS, Forster, Redding and Lee dies on my bench. I have found over time that I prefer the Hornady locking ring design. The ring is easily tightened with the included hex key. This design tensions the entire bearing surface of the ring, rather than a single point-of-contact set-screw.
When I buy a new non-Hornady die, the first thing I do is replace the locking ring with one of these.
Hornady Die lock rings(25-07-2017)
Nothing bothers me more than poorly designed die lock rings. My past history of 45 years of reloading began with the old RCBS lead pellet/setscrew system that impinged on the 7/8-14 threads of the die making it very difficult to adjust or remove off the die. Advancements then used brass setscrews then angled split ring design at a tangent to the threads which adjusted themselves closed against the threads,a much improved version.These Hornady lock rings allow their propriatory red handled wrench to properly secure this split ring tightly against the press body. Other manufacturers use their wrenches but still use the old setscrew that crushes against the die threads. I recommend these lock rings over any other type to include "O" ring spongy attachments.