Kolimator EGW jest przeznaczony do montażu od lewej do prawej strony (z lufą skierowaną do przodu). Szyna ma progresywne zwężenie, aby ułatwić instalację. Wystarczy usunąć tylną przyrząd celowniczy z broni i zastąpić go montażem EGW, aby zamontować kolimator Leupold DeltaPoint Pro, JPoint, Redfield Accelerator lub Optima. Montaż można w każdej chwili zdjąć i zastąpić tylną przyrząd celowniczy. Zestaw zawiera niezbędne elementy montażowe. Instrukcja instalacji Usuń tylną przyrząd celowniczy* Zainstaluj montaż EGW w rowku Dociskaj śrubę ustalającą (jeśli dotyczy) Umieść kolimator na montażu EGW (umieszczenie małego kawałka papieru między kolimatorem a montażem ułatwi późniejsze usunięcie i ochroni kolimator przed Loctite.) Nałóż niebieski Loctite na dołączone śruby montażowe Dokręć śruby montażowe z momentem 15in/lbs Modyfikacja broni może unieważnić gwarancję producenta. Produkt powinien być zainstalowany i sprawdzony przez kwalifikowanego rusznikarza. Nie ponosimy odpowiedzialności za szkody lub obrażenia, które mogą wyniknąć z niewłaściwej instalacji lub użytkowania tego produktu. Montaż pasuje do: Colt 1911/.22 Rail Gun (szyna Walther .22) Montaż pasuje do pistoletu Colt Rail Gun .22lr z suwadłem wykonanym przez Walther.
Więcej...
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mountwill make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Colt 1911/.22 Rail Gun (Walther .22 Slide) This mount fits the Colt Rail Gun .22lr that has the slide made by Walther.
Więcej...
001PLN
Nr produktu: 296000679 EGW WALTHER 22 LEUPOLD DELTAPOINT PRO SIGHT MOUNT Numer części: 49404841370115679 Kolimator EGW jest przeznaczony do montażu od lewej do prawej strony (z lufą skierowaną do przodu). Szyna ma progresywne zwężenie, aby ułatwić instalację. Wystarczy usunąć tylną przyrząd celowniczy z broni i zastąpić go montażem EGW, aby zamontować kolimator Leupold DeltaPoint Pro, JPoint, Redfield Accelerator lub Optima. Montaż można w każdej chwili zdjąć i zastąpić tylną przyrząd celowniczy. Zestaw zawiera niezbędne elementy montażowe. Instrukcja instalacji Usuń tylną przyrząd celowniczy* Zainstaluj montaż EGW w rowku Dociskaj śrubę ustalającą (jeśli dotyczy) Umieść kolimator na montażu EGW (umieszczenie małego kawałka papieru między kolimatorem a montażem ułatwi późniejsze usunięcie i ochroni kolimator przed Loctite.) Nałóż niebieski Loctite na dołączone śruby montażowe Dokręć śruby montażowe z momentem 15in/lbs Modyfikacja broni może unieważnić gwarancję producenta. Produkt powinien być zainstalowany i sprawdzony przez kwalifikowanego rusznikarza. Nie ponosimy odpowiedzialności za szkody lub obrażenia, które mogą wyniknąć z niewłaściwej instalacji lub użytkowania tego produktu. Montaż pasuje do: Colt 1911/.22 Rail Gun (szyna Walther .22) Montaż pasuje do pistoletu Colt Rail Gun .22lr z suwadłem wykonanym przez Walther.
Kolimator EGW jest przeznaczony do montażu od lewej do prawej strony (z lufą skierowaną do przodu). Szyna ma progresywne zwężenie, aby ułatwić instalację. Wystarczy usunąć tylną przyrząd celowniczy z broni i zastąpić go montażem EGW, aby zamontować kolimator Leupold DeltaPoint Pro, JPoint, Redfield Accelerator lub Optima. Montaż można w każdej chwili zdjąć i zastąpić tylną przyrząd celowniczy. Zestaw zawiera niezbędne elementy montażowe. Instrukcja instalacji Usuń tylną przyrząd celowniczy* Zainstaluj montaż EGW w rowku Dociskaj śrubę ustalającą (jeśli dotyczy) Umieść kolimator na montażu EGW (umieszczenie małego kawałka papieru między kolimatorem a montażem ułatwi późniejsze usunięcie i ochroni kolimator przed Loctite.) Nałóż niebieski Loctite na dołączone śruby montażowe Dokręć śruby montażowe z momentem 15in/lbs Modyfikacja broni może unieważnić gwarancję producenta. Produkt powinien być zainstalowany i sprawdzony przez kwalifikowanego rusznikarza. Nie ponosimy odpowiedzialności za szkody lub obrażenia, które mogą wyniknąć z niewłaściwej instalacji lub użytkowania tego produktu. Montaż pasuje do: Colt 1911/.22 Rail Gun (szyna Walther .22) Montaż pasuje do pistoletu Colt Rail Gun .22lr z suwadłem wykonanym przez Walther.
Więcej...
EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mountwill make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Colt 1911/.22 Rail Gun (Walther .22 Slide) This mount fits the Colt Rail Gun .22lr that has the slide made by Walther.