Szybki i łatwy montaż celownika red dot na Twoim Smith & Wesson Model 52!
Oferujemy montaż celownika S&W 52 VORTEX VIPER/VENOM od marki EGW, który jest idealnym rozwiązaniem dla miłośników strzelectwa. Nasze celowniki red dot są zaprojektowane do montażu z lewej na prawą stronę (z wylotem lufy skierowanym do przodu).
Opis produktu:
Dzięki progresywnemu taperowi w rowku, montaż jest łatwiejszy do zainstalowania. Wystarczy zdjąć tylny celownik z broni i wymienić go na montaż, aby zamontować celownik Vortex Viper/Venom, Burris FastFire lub Docter. Montaż można łatwo zdjąć i w każdej chwili przywrócić tylny celownik.
Instrukcje instalacji:
- Usuń tylny celownik*
- Zainstaluj montaż EGW w rowku
- Dokręć śrubę mocującą (jeśli dotyczy)
- Umieść celownik red dot na montażu EGW (umieszczenie małego kawałka papieru między celownikiem a montażem ułatwi demontaż i zapobiegnie dostaniu się Loctite na celownik).
- Nałóż niebieski Loctite na dostarczone śruby montażowe
- Dokręć śruby montażowe do 15in/lbs
W zestawie:
- 2 Śruby z główką typu Button Head - dostarczone do celowników Vortex Viper i Venom
- 2 Śruby z główką typu Flat Head - dostarczone do celowników Burris FastFire i Docter
Śruby dołączone do tego montażu wymagają klucza imbusowego 5/64'' do instalacji. Modyfikacja Twojej broni może unieważnić gwarancję producenta. Ten produkt powinien być zainstalowany i sprawdzony przez wykwalifikowanego rusznikarza. Nie ponosimy odpowiedzialności za uszkodzenia lub obrażenia, które mogą wyniknąć z niewłaściwej instalacji lub użytkowania tego produktu.
Kompatybilność:
- Ten montaż pasuje do: Smith & Wesson Model 52
- Ten montaż nie pasuje do: Smith & Wesson Model 41
EGW's red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Smith & Wesson Model 52 This mount does not fit: Smith & Wesson Model 41