Nowy montaż do celowników Vortex Viper/Venom od EGW!
Ten montaż nie jest częścią, którą można po prostu włożyć i wymaga dopasowania. Celowniki red dot EGW powinny być instalowane od lewej do prawej (z lufą skierowaną do przodu). Dovetail ma progresywny taper, co ułatwia instalację.
Aby zamontować swój celownik Vortex Viper/Venom, Burris FastFire lub Docter, wystarczy zdjąć tylny celownik z broni i zastąpić go montażem EGW. Montaż można w każdej chwili zdjąć i wymienić tylny celownik. W zestawie znajduje się sprzęt montażowy. Produkty EGW powinny być instalowane i sprawdzane przez wykwalifikowanego i kompetentnego rusznikarza.
Instrukcje instalacji:
- Usuń tylny celownik*
- Zainstaluj montaż EGW w dovetailu po sprawdzeniu dopasowania
- Dokręć śrubę ustalającą (jeśli dotyczy)
- Umieść celownik red dot na montażu EGW (umieszczenie małego kawałka papieru między celownikiem red dot a montażem ułatwi demontaż i zapobiegnie zabrudzeniu Loctite'em celownika).
- Nałóż niebieski Loctite na dostarczone śruby montażowe
- Dokręć śruby montażowe do 15in/lbs
2 śruby z główką typu Button Head - dostarczone dla celowników Vortex Viper i Venom
2 śruby z główką typu Flat Head - dostarczone dla celowników Burris FastFire i Docter
Śruby dołączone do tego montażu wymagają klucza imbusowego 5/64'' do instalacji. Modyfikacja twojej broni może unieważnić gwarancję producenta. Produkt ten powinien być instalowany i sprawdzany przez wykwalifikowanego rusznikarza. Nie ponosimy odpowiedzialności za uszkodzenia lub obrażenia, które mogą wyniknąć z niewłaściwej instalacji lub użycia tego produktu.
Ten montaż pasuje do:
Broni z powiększonymi dovetailami typu Novak. Ten montaż jest wykonany o .007'' większy niż standardowe wycięcie Novak i wymaga dopasowania.
This mount is NOT a drop in part and will require fitting. EGW red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Simply remove the rear sight on your gun and replace it with EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take the mount off and replace your rear sight at any time. Mounting hardware included. EGW products should be installed and checked by a qualified and competent gunsmith. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail after checking for fit Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs 2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights 2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights The screws that are included with this mount require a 5/64'' allen wrench for installation. Modification of your firearm may nullify the manufacturer's warranty. This product should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. This mount fits: Firearms with oversized Novak cut dovetails. This mount is made .007"" larger than a standard Novak cut and will require fitting.