Twój koszyk jest pusty.

Koszyk

Newsletter

WILSON COMBAT
1911 MULTI-COMP

874218001674 965397001

Natychmiastowa kontrola wylotu i tuleja redukująca odrzut

Trzy pełne komory i siedem otworów wylotowych łączą się, aby pomóc kontrolować odrzut i podnoszenie lufy, co pozwala szybciej powrócić na cel. Instalacja jest tak prosta, jak montaż nowej tulei lufy. Pasuje do wszystkich kalibrów luf o długości rządowej z zewnętrzną średnicą od .576" do .580". Wymaga drobnej obróbki i pełnowymiarowego, dwuczęściowego sprężynowego prowadnika lufy.

SPECS: Stal, wykończenie matowe, niebieskie. Długość 2" (4.8cm).

Więcej...

Instant Comp & Bushing Give Muzzle Control, Less Recoil

Three full chambers and seven exhaust ports combine to help control recoil and muzzle climb to put you back on target faster. Installation is as easy as fitting a new barrel bushing. Fits all calibers of Govt.-length barrels with O.D. of .576" to .580". Requires minor fitting and a full-length, two-piece guide rod.

SPECS: Steel, blued, matte finish. 2" (4.8cm) long.

Więcej...

Oceny klientów dla WILSON COMBAT MULTI-COMP

Liczba ocen: 13
Od brownells.com: 13
Średnia ocena: 4,6

Best one to Buy (29-07-2009)

This compensator work. This my third one on my 1911(Colt, Para Ord., and SW). my grouping is less than 1" on 25m.

works as advertized (14-08-2009)

The Multi-comp definitely reduces muzzle rise. It was easy to install.

multi comp (22-02-2010)

great is all i can say, this was truly a drop in addition to my pistol and on top of making it look even more awsome it also reduces the muzzle flip a little bit. it added just over 1 1/4"s to the overall length, and it was a great addition to my pistol. along side the black gritty punisher grips and the 10 round mags that i have purchased for it this tops all of them. there was no fitting required at all.

Good full size compensator. (08-01-2011)

Every review about drop-in fit is accurate. If you are performing a custom build like I did, here are a few things I ran across. Pre-measure your opening on your slide and the comp. OD. I had to mill off .0015" for a nice snug fit. My set up was with an STI 6" long slide and barrel which extended just beyond the slide. Checking proper fit I found that I had to lathe about .002" from the ID of the comp. to clear the barrel. Wilson also recommends shortening the spring plug to 1.2".
Hope this helps.

.45 Comp (26-01-2011)

Great addition to my custom .45. Gives it a more tactical look and increases it's "scare factor". It was difficult to install, and it's curves don't quite match up with the slide. Slightly noticeable difference in recoil as well helps with faster follow-up shots. On the full size 1911 it almost makes it awkwardly long as far as carry and look goes so in my opinion would look better on a commander sized or smaller.

Well worth the effort (06-03-2011)

THis took considerable fitting on my S&W 1911. Not a hard process but time consuming. I installed it with a Wolf 14# reduced power main spring and the Wilson 2 piece guide rod w shock buffer. I shot the gun side by side with a stock S&W 1911 and could readily feel the difference with ammo ranging from target velocity 200 gr loads to factory ball. Considerably less muzzle flip and felt recoil on all loads. Accuracy may have been slightly improved as well. It's a bit of a pain to clean but well worth it IMHO

I'd have given it a 5 if it was true drop in.

Awesome product (12-03-2012)

I use this on my Kimber 45 for shooting targets and hunting. It is the best investment that I have made for my Kimber so far. As it says in the details mill work is required and anyone who gives a bad rating for that reason did not read or understand what is written.

Fit and Finish (09-04-2012)

Instructions say "May need to be fitted". This was absolutely NOT the case with the Springfield M1911 A1. Tolerances are slightly different from gun to gun, but with moderate pressure and twist, the part fit the Springfield very nicely. Noticable difference in recoil and it looks good. Thank you Brownells and Wilson Combat

Works and looks great! (03-02-2013)

This was a drop in fit for my 1911! The first time I had it to the range I noticed a big difference in muzzle jump, and my follow up shots were a lot quicker. This looks really awesome as well!

Awesome product! READ THE INSTRUCTIONS! (10-08-2013)

I bought this for my Colt 1991 1A, it took some time to get the OD of the comp to the correct diameter, THIS IS NOT A "DROP IN" part! Take your time, check the fit periodically (You don't want any slop here) also I highly recommend you also get the WC 2 piece guide rod for the spring, I did not have to remove any of the spring at all but assembly is much easier with the two piece rod, not to mention its another great upgrade as it keeps any spring binding from happening, just read the instructions

REALLY HAPPY (16-04-2014)

PUT THIS ON MY ISRAEL ARMS M-5000 GAL, TOOK JUST A FEW MINS TO DO SOME VERY SMALL FITTING. WORKS LIKE A CHARM AND LOOKS GOOD TOO!

Stainless Multi-Comp on SA 1911 "Loaded" (25-05-2015)

Added the Stainless Multi-Comp to my Springfield Armory "Loaded" 1911. The I.D. of the comp matched the O.D. of the SA barrel perfectly. My dial caliper showed a .0015" difference -- just enough for a thin film of lubricant! I use this 1911 in IDPA at our local range at it has helped. In "regular" target shooting, I consistently shoot 2" groups at 10 yards and that's shooting 8 rounds in 10 seconds. A very nice addition to a great 1911!

<img width="500" src='/userdocs/reviewimages/230cdbea-66b5-42c5-8813-40a144d8db46.jpg' alt=''>

Use Caution. (12-06-2015)

Very nice looking addition to my Springfield Range Officer. Installation is time consuming and it took quite a bit of time and emery cloth to get it to fit the slide. Barrel fit perfectly with no adjustments needed.

The caution is, at least with my Range Officer it makes dissassembly much more difficult as the front spring plug cannot be remove or installed with the Multi-Comp installed on the slide. plug must be installed, then the Multi-Comp, then the spring and spring guide held in place by hand and installed on the lower. Tricky to say the least.

Zobacz 13 dodatkowych opinii na brownells.com

579 579 1 PLN

Nr produktu: 965397001
WILSON COMBAT MULTI-COMP
Numer części: 397 874218001674 Trzy pełne komory i siedem otworów wylotowych łączą się, aby pomóc kontrolować odrzut i podnoszenie lufy, co pozwala szybciej powrócić na cel. Instalacja jest tak prosta, jak montaż nowej tulei lufy. Pasuje do wszystkich kalibrów luf o długości rządowej z zewnętrzną średnicą od .576" do .580". Wymaga drobnej obróbki i pełnowymiarowego, dwuczęściowego sprężynowego prowadnika lufy.

579 PLN 2 579,00 zł *

Czas dostawy ok. 14-21 dni.
2 szt. w magazynie w USA

Specyfikacja: Make: 1911 Model: Government

Dodaj do listy zakupów

Zapytaj

Szczegóły

Dodaj do listy zakupów

Zapytaj

Top takeaways

Trzy pełne komory i siedem otworów wylotowych pomagają kontrolować odrzut i podnoszenie lufy, umożliwiając szybszy powrót na cel.
Instalacja jest prosta i wymaga montażu nowej tulei lufy oraz drobnej obróbki.
Pasuje do luf o długości rządowej z zewnętrzną średnicą od .576" do .580" i wymaga pełnowymiarowego, dwuczęściowego sprężynowego prowadnika lufy.

Cechy

Model: Government Wytwórca: 1911 Waga dostawy: 0,059kg Wysokość wysyłki: 28mm Szerokość wysyłki: 79mm Długość wysyłki: 122mm

Szczegóły pozycji

Made in USA

Kompensator 1911 MULTI-COMP od Wilson Combat kontroluje odrzut i podnoszenie lufy. Pasuje do kalibrów rządowych. Prosta instalacja. Dowiedz się więcej! 🔫✨

Natychmiastowa kontrola wylotu i tuleja redukująca odrzut

SPECS: Stal, wykończenie matowe, niebieskie. Długość 2" (4.8cm).

Więcej...

Instant Comp & Bushing Give Muzzle Control, Less Recoil

SPECS: Steel, blued, matte finish. 2" (4.8cm) long.

Więcej...

Oceny klientów dla WILSON COMBAT MULTI-COMP

Liczba ocen: 13
Od brownells.com: 13
Średnia ocena: 4,6

Best one to Buy (29-07-2009)

This compensator work. This my third one on my 1911(Colt, Para Ord., and SW). my grouping is less than 1" on 25m.

works as advertized (14-08-2009)

The Multi-comp definitely reduces muzzle rise. It was easy to install.

multi comp (22-02-2010)

Good full size compensator. (08-01-2011)

.45 Comp (26-01-2011)

Well worth the effort (06-03-2011)

Awesome product (12-03-2012)

Fit and Finish (09-04-2012)

Works and looks great! (03-02-2013)

This was a drop in fit for my 1911! The first time I had it to the range I noticed a big difference in muzzle jump, and my follow up shots were a lot quicker. This looks really awesome as well!

Awesome product! READ THE INSTRUCTIONS! (10-08-2013)

REALLY HAPPY (16-04-2014)

PUT THIS ON MY ISRAEL ARMS M-5000 GAL, TOOK JUST A FEW MINS TO DO SOME VERY SMALL FITTING. WORKS LIKE A CHARM AND LOOKS GOOD TOO!

Stainless Multi-Comp on SA 1911 "Loaded" (25-05-2015)

Use Caution. (12-06-2015)

Zobacz 13 dodatkowych opinii na brownells.com

Sugerowane pozycje
Klienci kupili także

WOLFF EXTRA POWER BASE PIN SPRINGS, RUGER
EXTRA POWER BASE PIN SPRINGS

WOLFF

Zamówione ponownie

84,00 zł *

Sprężyny osi bębna typu Base Pin

WOLFF FIRING PIN SAFETY BLOCK SPRING, 3-PAK
1911 AUTO FIRING PIN SAFETY BLOCK SPRING

WOLFF

Zamówione ponownie

119,00 zł *

Sprężyny igliczne

WILSON COMBAT EXTENDED EJECTOR (B)
1911 "FACTORY PLUS" EJECTOR

WILSON COMBAT

W magazynie

239,00 zł *

Rozładowniki

SPRINGFIELD ARMORY 45 ACP BARREL LINK ®1911 STAINLESS STEEL
1911 BARREL LINK

SPRINGFIELD ARMORY

Zamówione ponownie

99,00 zł *

Ogniwka łącznika ruchomego

ZEV TECHNOLOGIES PRO TRIGGER KIT 9/40 GEN 4 BLACK SAFETY
PRO SERIES DROP-IN TRIGGER KITS FOR GLOCK® GEN 4

ZEV TECHNOLOGIES

Niedostępne

Spusty

Odkryj nakładki HANDALL Beavertail Grip Sleeve do Glock 17/19X/34! 🖐️ Zapewniają idealne dopasowanie, ochronę i komfort. Trwałe i antypoślizgowe. Dowiedz się więcej!

HOGUE HANDALL BEAVERTAIL GRIP SLEEVE BLK GLOCK 17/19X/34 G1-2-5
HANDALL BEAVERTAIL GRIP SLEEVES

HOGUE

W magazynie

129,00 zł * 99,00 zł - 129,00 zł*

Chwyty

4,4

BERETTA USA BERETTA 92FS DUCKS UNLIMITED SLIDE ASSEMBLY
BERETTA 92FS DUCKS UNLIMITED SLIDE ASSEMBLY

BERETTA USA

Niedostępne

Zamki pistoletowe

ED BROWN COMMANDER RECOIL SPRING PLUG, STAINLESS
1911 RECOIL SPRING PLUGS

ED BROWN

W magazynie

109,00 zł * 104,00 zł - 109,00 zł*

Zatyczki sprężyny powrotnej

4,5

Zaloguj się

Nie pamiętasz hasła?
Zarejestruj się

Kontakt

Mapa strony

Kategorie produktów

Zamawianie

Obsługa klienta

Witamy!

Witamy w brownells.pl wiodącym dostawcy w Polsce akcesoriów do broni, części broni, narzędzi rusznikarskich, narzędzi do elaboracji amunicji oraz komponentów.

Co oferujemy

Lubisz strzelać, pracujesz przy naprawach broni zawodowo lub hobbystycznie lub po prostu jesteś właścicielem broni, to nasza strona jest właśnie dla Ciebie!

Przez ponad 75 lat strzelcy, rusznikarze, hobbyści, wojskowi, służby specjalne korzystają z usług Brownells jako dostawcy szerokiego asortymentu, wysokiej jakości części broni. Znajdziesz ponad 90 000 produktów w tym części nietypowe, akcesoria, narzędzia rusznikarskie i inne produkty do utrzymania, naprawy i ulepszania swojej broni.